summaryrefslogtreecommitdiffstats
path: root/hosts/profitbricks-build4-amd64/etc
diff options
context:
space:
mode:
Diffstat (limited to 'hosts/profitbricks-build4-amd64/etc')
-rw-r--r--hosts/profitbricks-build4-amd64/etc/squid3/squid.conf5787
1 files changed, 5787 insertions, 0 deletions
diff --git a/hosts/profitbricks-build4-amd64/etc/squid3/squid.conf b/hosts/profitbricks-build4-amd64/etc/squid3/squid.conf
new file mode 100644
index 00000000..697e59c0
--- /dev/null
+++ b/hosts/profitbricks-build4-amd64/etc/squid3/squid.conf
@@ -0,0 +1,5787 @@
+# WELCOME TO SQUID 3.1.20
+# ----------------------------
+#
+# This is the documentation for the Squid configuration file.
+# This documentation can also be found online at:
+# http://www.squid-cache.org/Doc/config/
+#
+# You may wish to look at the Squid home page and wiki for the
+# FAQ and other documentation:
+# http://www.squid-cache.org/
+# http://wiki.squid-cache.org/SquidFaq
+# http://wiki.squid-cache.org/ConfigExamples
+#
+# This documentation shows what the defaults for various directives
+# happen to be. If you don't need to change the default, you should
+# leave the line out of your squid.conf in most cases.
+#
+# In some cases "none" refers to no default setting at all,
+# while in other cases it refers to the value of the option
+# - the comments for that keyword indicate if this is the case.
+#
+
+# Configuration options can be included using the "include" directive.
+# Include takes a list of files to include. Quoting and wildcards are
+# supported.
+#
+# For example,
+#
+# include /path/to/included/file/squid.acl.config
+#
+# Includes can be nested up to a hard-coded depth of 16 levels.
+# This arbitrary restriction is to prevent recursive include references
+# from causing Squid entering an infinite loop whilst trying to load
+# configuration files.
+
+# TAG: dns_testnames
+# Remove this line. DNS is no longer tested on startup.
+#Default:
+# none
+
+# TAG: extension_methods
+# Remove this line. All valid methods for HTTP are accepted by default.
+#Default:
+# none
+
+# TAG: incoming_rate
+#Default:
+# none
+
+# TAG: server_http11
+# Remove this line. HTTP/1.1 is supported by default.
+#Default:
+# none
+
+# TAG: upgrade_http0.9
+# Remove this line. ICY/1.0 streaming protocol is supported by default.
+#Default:
+# none
+
+# TAG: zph_local
+# Alter these entries. Use the qos_flows directive instead.
+#Default:
+# none
+
+# TAG: header_access
+# Since squid-3.0 replace with request_header_access or reply_header_access
+# depending on whether you wish to match client requests or server replies.
+#Default:
+# none
+
+# TAG: httpd_accel_no_pmtu_disc
+# Since squid-3.0 use the 'disable-pmtu-discovery' flag on http_port instead.
+#Default:
+# none
+
+# OPTIONS FOR AUTHENTICATION
+# -----------------------------------------------------------------------------
+
+# TAG: auth_param
+# This is used to define parameters for the various authentication
+# schemes supported by Squid.
+#
+# format: auth_param scheme parameter [setting]
+#
+# The order in which authentication schemes are presented to the client is
+# dependent on the order the scheme first appears in config file. IE
+# has a bug (it's not RFC 2617 compliant) in that it will use the basic
+# scheme if basic is the first entry presented, even if more secure
+# schemes are presented. For now use the order in the recommended
+# settings section below. If other browsers have difficulties (don't
+# recognize the schemes offered even if you are using basic) either
+# put basic first, or disable the other schemes (by commenting out their
+# program entry).
+#
+# Once an authentication scheme is fully configured, it can only be
+# shutdown by shutting squid down and restarting. Changes can be made on
+# the fly and activated with a reconfigure. I.E. You can change to a
+# different helper, but not unconfigure the helper completely.
+#
+# Please note that while this directive defines how Squid processes
+# authentication it does not automatically activate authentication.
+# To use authentication you must in addition make use of ACLs based
+# on login name in http_access (proxy_auth, proxy_auth_regex or
+# external with %LOGIN used in the format tag). The browser will be
+# challenged for authentication on the first such acl encountered
+# in http_access processing and will also be re-challenged for new
+# login credentials if the request is being denied by a proxy_auth
+# type acl.
+#
+# WARNING: authentication can't be used in a transparently intercepting
+# proxy as the client then thinks it is talking to an origin server and
+# not the proxy. This is a limitation of bending the TCP/IP protocol to
+# transparently intercepting port 80, not a limitation in Squid.
+# Ports flagged 'transparent', 'intercept', or 'tproxy' have
+# authentication disabled.
+#
+# === Parameters for the basic scheme follow. ===
+#
+# "program" cmdline
+# Specify the command for the external authenticator. Such a program
+# reads a line containing "username password" and replies "OK" or
+# "ERR" in an endless loop. "ERR" responses may optionally be followed
+# by a error description available as %m in the returned error page.
+# If you use an authenticator, make sure you have 1 acl of type
+# proxy_auth.
+#
+# By default, the basic authentication scheme is not used unless a
+# program is specified.
+#
+# If you want to use the traditional NCSA proxy authentication, set
+# this line to something like
+#
+# auth_param basic program /usr/lib/squid3/ncsa_auth /usr/etc/passwd
+#
+# "utf8" on|off
+# HTTP uses iso-latin-1 as characterset, while some authentication
+# backends such as LDAP expects UTF-8. If this is set to on Squid will
+# translate the HTTP iso-latin-1 charset to UTF-8 before sending the
+# username & password to the helper.
+#
+# "children" numberofchildren
+# The number of authenticator processes to spawn. If you start too few
+# Squid will have to wait for them to process a backlog of credential
+# verifications, slowing it down. When password verifications are
+# done via a (slow) network you are likely to need lots of
+# authenticator processes.
+# auth_param basic children 5
+#
+# "concurrency" concurrency
+# The number of concurrent requests the helper can process.
+# The default of 0 is used for helpers who only supports
+# one request at a time. Setting this changes the protocol used to
+# include a channel number first on the request/response line, allowing
+# multiple requests to be sent to the same helper in parallell without
+# wating for the response.
+# Must not be set unless it's known the helper supports this.
+# auth_param basic concurrency 0
+#
+# "realm" realmstring
+# Specifies the realm name which is to be reported to the
+# client for the basic proxy authentication scheme (part of
+# the text the user will see when prompted their username and
+# password). There is no default.
+# auth_param basic realm Squid proxy-caching web server
+#
+# "credentialsttl" timetolive
+# Specifies how long squid assumes an externally validated
+# username:password pair is valid for - in other words how
+# often the helper program is called for that user. Set this
+# low to force revalidation with short lived passwords. Note
+# setting this high does not impact your susceptibility
+# to replay attacks unless you are using an one-time password
+# system (such as SecureID). If you are using such a system,
+# you will be vulnerable to replay attacks unless you also
+# use the max_user_ip ACL in an http_access rule.
+#
+# "casesensitive" on|off
+# Specifies if usernames are case sensitive. Most user databases are
+# case insensitive allowing the same username to be spelled using both
+# lower and upper case letters, but some are case sensitive. This
+# makes a big difference for user_max_ip ACL processing and similar.
+# auth_param basic casesensitive off
+#
+# === Parameters for the digest scheme follow ===
+#
+# "program" cmdline
+# Specify the command for the external authenticator. Such
+# a program reads a line containing "username":"realm" and
+# replies with the appropriate H(A1) value hex encoded or
+# ERR if the user (or his H(A1) hash) does not exists.
+# See rfc 2616 for the definition of H(A1).
+# "ERR" responses may optionally be followed by a error description
+# available as %m in the returned error page.
+#
+# By default, the digest authentication scheme is not used unless a
+# program is specified.
+#
+# If you want to use a digest authenticator, set this line to
+# something like
+#
+# auth_param digest program /usr/lib/squid3/digest_pw_auth /usr/etc/digpass
+#
+# "utf8" on|off
+# HTTP uses iso-latin-1 as characterset, while some authentication
+# backends such as LDAP expects UTF-8. If this is set to on Squid will
+# translate the HTTP iso-latin-1 charset to UTF-8 before sending the
+# username & password to the helper.
+#
+# "children" numberofchildren
+# The number of authenticator processes to spawn (no default).
+# If you start too few Squid will have to wait for them to
+# process a backlog of H(A1) calculations, slowing it down.
+# When the H(A1) calculations are done via a (slow) network
+# you are likely to need lots of authenticator processes.
+# auth_param digest children 5
+#
+# "realm" realmstring
+# Specifies the realm name which is to be reported to the
+# client for the digest proxy authentication scheme (part of
+# the text the user will see when prompted their username and
+# password). There is no default.
+# auth_param digest realm Squid proxy-caching web server
+#
+# "nonce_garbage_interval" timeinterval
+# Specifies the interval that nonces that have been issued
+# to client_agent's are checked for validity.
+#
+# "nonce_max_duration" timeinterval
+# Specifies the maximum length of time a given nonce will be
+# valid for.
+#
+# "nonce_max_count" number
+# Specifies the maximum number of times a given nonce can be
+# used.
+#
+# "nonce_strictness" on|off
+# Determines if squid requires strict increment-by-1 behavior
+# for nonce counts, or just incrementing (off - for use when
+# useragents generate nonce counts that occasionally miss 1
+# (ie, 1,2,4,6)). Default off.
+#
+# "check_nonce_count" on|off
+# This directive if set to off can disable the nonce count check
+# completely to work around buggy digest qop implementations in
+# certain mainstream browser versions. Default on to check the
+# nonce count to protect from authentication replay attacks.
+#
+# "post_workaround" on|off
+# This is a workaround to certain buggy browsers who sends
+# an incorrect request digest in POST requests when reusing
+# the same nonce as acquired earlier on a GET request.
+#
+# === NTLM scheme options follow ===
+#
+# "program" cmdline
+# Specify the command for the external NTLM authenticator.
+# Such a program reads exchanged NTLMSSP packets with
+# the browser via Squid until authentication is completed.
+# If you use an NTLM authenticator, make sure you have 1 acl
+# of type proxy_auth. By default, the NTLM authenticator_program
+# is not used.
+#
+# auth_param ntlm program /usr/lib/squid3/ntlm_auth
+#
+# "children" numberofchildren
+# The number of authenticator processes to spawn (no default).
+# If you start too few Squid will have to wait for them to
+# process a backlog of credential verifications, slowing it
+# down. When credential verifications are done via a (slow)
+# network you are likely to need lots of authenticator
+# processes.
+#
+# auth_param ntlm children 5
+#
+# "keep_alive" on|off
+# Whether to keep the connection open after the initial response where
+# Squid tells the browser which schemes are supported by the proxy.
+# Some browsers are known to present many login popups or to corrupt
+# POST/PUT requests transfer if the connection is not closed.
+# The default is currently OFF to avoid this, but may change.
+#
+# auth_param ntlm keep_alive on
+#
+# === Options for configuring the NEGOTIATE auth-scheme follow ===
+#
+# "program" cmdline
+# Specify the command for the external Negotiate authenticator.
+# This protocol is used in Microsoft Active-Directory enabled setups with
+# the Microsoft Internet Explorer or Mozilla Firefox browsers.
+# Its main purpose is to exchange credentials with the Squid proxy
+# using the Kerberos mechanisms.
+# If you use a Negotiate authenticator, make sure you have at least
+# one acl of type proxy_auth active. By default, the negotiate
+# authenticator_program is not used.
+# The only supported program for this role is the ntlm_auth
+# program distributed as part of Samba, version 4 or later.
+#
+# auth_param negotiate program /usr/lib/squid3/ntlm_auth --helper-protocol=gss-spnego
+#
+# "children" numberofchildren
+# The number of authenticator processes to spawn (no default).
+# If you start too few Squid will have to wait for them to
+# process a backlog of credential verifications, slowing it
+# down. When crendential verifications are done via a (slow)
+# network you are likely to need lots of authenticator
+# processes.
+# auth_param negotiate children 5
+#
+# "keep_alive" on|off
+# Whether to keep the connection open after the initial response where
+# Squid tells the browser which schemes are supported by the proxy.
+# Some browsers are known to present many login popups or to corrupt
+# POST/PUT requests transfer if the connection is not closed.
+# The default is currently OFF to avoid this, but may change.
+#
+# auth_param negotiate keep_alive on
+#
+#
+# Examples:
+#
+##Recommended minimum configuration per scheme:
+##auth_param negotiate program <uncomment and complete this line to activate>
+##auth_param negotiate children 5
+##auth_param negotiate keep_alive on
+##
+##auth_param ntlm program <uncomment and complete this line to activate>
+##auth_param ntlm children 5
+##auth_param ntlm keep_alive on
+##
+##auth_param digest program <uncomment and complete this line>
+##auth_param digest children 5
+##auth_param digest realm Squid proxy-caching web server
+##auth_param digest nonce_garbage_interval 5 minutes
+##auth_param digest nonce_max_duration 30 minutes
+##auth_param digest nonce_max_count 50
+##
+##auth_param basic program <uncomment and complete this line>
+##auth_param basic children 5
+##auth_param basic realm Squid proxy-caching web server
+##auth_param basic credentialsttl 2 hours
+#Default:
+# none
+
+# TAG: authenticate_cache_garbage_interval
+# The time period between garbage collection across the username cache.
+# This is a tradeoff between memory utilization (long intervals - say
+# 2 days) and CPU (short intervals - say 1 minute). Only change if you
+# have good reason to.
+#Default:
+# authenticate_cache_garbage_interval 1 hour
+
+# TAG: authenticate_ttl
+# The time a user & their credentials stay in the logged in
+# user cache since their last request. When the garbage
+# interval passes, all user credentials that have passed their
+# TTL are removed from memory.
+#Default:
+# authenticate_ttl 1 hour
+
+# TAG: authenticate_ip_ttl
+# If you use proxy authentication and the 'max_user_ip' ACL,
+# this directive controls how long Squid remembers the IP
+# addresses associated with each user. Use a small value
+# (e.g., 60 seconds) if your users might change addresses
+# quickly, as is the case with dialups. You might be safe
+# using a larger value (e.g., 2 hours) in a corporate LAN
+# environment with relatively static address assignments.
+#Default:
+# authenticate_ip_ttl 0 seconds
+
+# ACCESS CONTROLS
+# -----------------------------------------------------------------------------
+
+# TAG: external_acl_type
+# This option defines external acl classes using a helper program
+# to look up the status
+#
+# external_acl_type name [options] FORMAT.. /path/to/helper [helper arguments..]
+#
+# Options:
+#
+# ttl=n TTL in seconds for cached results (defaults to 3600
+# for 1 hour)
+# negative_ttl=n
+# TTL for cached negative lookups (default same
+# as ttl)
+# children=n Number of acl helper processes spawn to service
+# external acl lookups of this type. (default 5)
+# concurrency=n concurrency level per process. Only used with helpers
+# capable of processing more than one query at a time.
+# cache=n result cache size, 0 is unbounded (default)
+# grace=n Percentage remaining of TTL where a refresh of a
+# cached entry should be initiated without needing to
+# wait for a new reply. (default 0 for no grace period)
+# protocol=2.5 Compatibility mode for Squid-2.5 external acl helpers
+# ipv4 / ipv6 IP protocol used to communicate with this helper.
+# The default is to auto-detect IPv6 and use it when available.
+#
+# FORMAT specifications
+#
+# %LOGIN Authenticated user login name
+# %EXT_USER Username from external acl
+# %IDENT Ident user name
+# %SRC Client IP
+# %SRCPORT Client source port
+# %URI Requested URI
+# %DST Requested host
+# %PROTO Requested protocol
+# %PORT Requested port
+# %PATH Requested URL path
+# %METHOD Request method
+# %MYADDR Squid interface address
+# %MYPORT Squid http_port number
+# %PATH Requested URL-path (including query-string if any)
+# %USER_CERT SSL User certificate in PEM format
+# %USER_CERTCHAIN SSL User certificate chain in PEM format
+# %USER_CERT_xx SSL User certificate subject attribute xx
+# %USER_CA_xx SSL User certificate issuer attribute xx
+#
+# %>{Header} HTTP request header "Header"
+# %>{Hdr:member}
+# HTTP request header "Hdr" list member "member"
+# %>{Hdr:;member}
+# HTTP request header list member using ; as
+# list separator. ; can be any non-alphanumeric
+# character.
+#
+# %<{Header} HTTP reply header "Header"
+# %<{Hdr:member}
+# HTTP reply header "Hdr" list member "member"
+# %<{Hdr:;member}
+# HTTP reply header list member using ; as
+# list separator. ; can be any non-alphanumeric
+# character.
+#
+# %% The percent sign. Useful for helpers which need
+# an unchanging input format.
+#
+# In addition to the above, any string specified in the referencing
+# acl will also be included in the helper request line, after the
+# specified formats (see the "acl external" directive)
+#
+# The helper receives lines per the above format specification,
+# and returns lines starting with OK or ERR indicating the validity
+# of the request and optionally followed by additional keywords with
+# more details.
+#
+# General result syntax:
+#
+# OK/ERR keyword=value ...
+#
+# Defined keywords:
+#
+# user= The users name (login)
+# password= The users password (for login= cache_peer option)
+# message= Message describing the reason. Available as %o
+# in error pages
+# tag= Apply a tag to a request (for both ERR and OK results)
+# Only sets a tag, does not alter existing tags.
+# log= String to be logged in access.log. Available as
+# %ea in logformat specifications
+#
+# If protocol=3.0 (the default) then URL escaping is used to protect
+# each value in both requests and responses.
+#
+# If using protocol=2.5 then all values need to be enclosed in quotes
+# if they may contain whitespace, or the whitespace escaped using \.
+# And quotes or \ characters within the keyword value must be \ escaped.
+#
+# When using the concurrency= option the protocol is changed by
+# introducing a query channel tag infront of the request/response.
+# The query channel tag is a number between 0 and concurrency-1.
+#Default:
+# none
+
+# TAG: acl
+# Defining an Access List
+#
+# Every access list definition must begin with an aclname and acltype,
+# followed by either type-specific arguments or a quoted filename that
+# they are read from.
+#
+# acl aclname acltype argument ...
+# acl aclname acltype "file" ...
+#
+# When using "file", the file should contain one item per line.
+#
+# By default, regular expressions are CASE-SENSITIVE.
+# To make them case-insensitive, use the -i option. To return case-sensitive
+# use the +i option between patterns, or make a new ACL line without -i.
+#
+# Some acl types require suspending the current request in order
+# to access some external data source.
+# Those which do are marked with the tag [slow], those which
+# don't are marked as [fast].
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl
+# for further information
+#
+# ***** ACL TYPES AVAILABLE *****
+#
+# acl aclname src ip-address/netmask ... # clients IP address [fast]
+# acl aclname src addr1-addr2/netmask ... # range of addresses [fast]
+# acl aclname dst ip-address/netmask ... # URL host's IP address [slow]
+# acl aclname myip ip-address/netmask ... # local socket IP address [fast]
+#
+# acl aclname arp mac-address ... (xx:xx:xx:xx:xx:xx notation)
+# # The arp ACL requires the special configure option --enable-arp-acl.
+# # Furthermore, the ARP ACL code is not portable to all operating systems.
+# # It works on Linux, Solaris, Windows, FreeBSD, and some
+# # other *BSD variants.
+# # [fast]
+# #
+# # NOTE: Squid can only determine the MAC address for clients that are on
+# # the same subnet. If the client is on a different subnet,
+# # then Squid cannot find out its MAC address.
+#
+# acl aclname srcdomain .foo.com ...
+# # reverse lookup, from client IP [slow]
+# acl aclname dstdomain .foo.com ...
+# # Destination server from URL [fast]
+# acl aclname srcdom_regex [-i] \.foo\.com ...
+# # regex matching client name [slow]
+# acl aclname dstdom_regex [-i] \.foo\.com ...
+# # regex matching server [fast]
+# #
+# # For dstdomain and dstdom_regex a reverse lookup is tried if a IP
+# # based URL is used and no match is found. The name "none" is used
+# # if the reverse lookup fails.
+#
+# acl aclname src_as number ...
+# acl aclname dst_as number ...
+# # [fast]
+# # Except for access control, AS numbers can be used for
+# # routing of requests to specific caches. Here's an
+# # example for routing all requests for AS#1241 and only
+# # those to mycache.mydomain.net:
+# # acl asexample dst_as 1241
+# # cache_peer_access mycache.mydomain.net allow asexample
+# # cache_peer_access mycache_mydomain.net deny all
+#
+# acl aclname peername myPeer ...
+# # [fast]
+# # match against a named cache_peer entry
+# # set unique name= on cache_peer lines for reliable use.
+#
+# acl aclname time [day-abbrevs] [h1:m1-h2:m2]
+# # [fast]
+# # day-abbrevs:
+# # S - Sunday
+# # M - Monday
+# # T - Tuesday
+# # W - Wednesday
+# # H - Thursday
+# # F - Friday
+# # A - Saturday
+# # h1:m1 must be less than h2:m2
+#
+# acl aclname url_regex [-i] ^http:// ...
+# # regex matching on whole URL [fast]
+# acl aclname urlpath_regex [-i] \.gif$ ...
+# # regex matching on URL path [fast]
+#
+# acl aclname port 80 70 21 0-1024... # destination TCP port [fast]
+# # ranges are alloed
+# acl aclname myport 3128 ... # local socket TCP port [fast]
+# acl aclname myportname 3128 ... # http(s)_port name [fast]
+#
+# acl aclname proto HTTP FTP ... # request protocol [fast]
+#
+# acl aclname method GET POST ... # HTTP request method [fast]
+#
+# acl aclname http_status 200 301 500- 400-403 ...
+# # status code in reply [fast]
+#
+# acl aclname browser [-i] regexp ...
+# # pattern match on User-Agent header (see also req_header below) [fast]
+#
+# acl aclname referer_regex [-i] regexp ...
+# # pattern match on Referer header [fast]
+# # Referer is highly unreliable, so use with care
+#
+# acl aclname ident username ...
+# acl aclname ident_regex [-i] pattern ...
+# # string match on ident output [slow]
+# # use REQUIRED to accept any non-null ident.
+#
+# acl aclname proxy_auth [-i] username ...
+# acl aclname proxy_auth_regex [-i] pattern ...
+# # perform http authentication challenge to the client and match against
+# # supplied credentials [slow]
+# #
+# # takes a list of allowed usernames.
+# # use REQUIRED to accept any valid username.
+# #
+# # Will use proxy authentication in forward-proxy scenarios, and plain
+# # http authenticaiton in reverse-proxy scenarios
+# #
+# # NOTE: when a Proxy-Authentication header is sent but it is not
+# # needed during ACL checking the username is NOT logged
+# # in access.log.
+# #
+# # NOTE: proxy_auth requires a EXTERNAL authentication program
+# # to check username/password combinations (see
+# # auth_param directive).
+# #
+# # NOTE: proxy_auth can't be used in a transparent/intercepting proxy
+# # as the browser needs to be configured for using a proxy in order
+# # to respond to proxy authentication.
+#
+# acl aclname snmp_community string ...
+# # A community string to limit access to your SNMP Agent [fast]
+# # Example:
+# #
+# # acl snmppublic snmp_community public
+#
+# acl aclname maxconn number
+# # This will be matched when the client's IP address has
+# # more than <number> TCP connections established. [fast]
+# # NOTE: This only measures direct TCP links so X-Forwarded-For
+# # indirect clients are not counted.
+#
+# acl aclname max_user_ip [-s] number
+# # This will be matched when the user attempts to log in from more
+# # than <number> different ip addresses. The authenticate_ip_ttl
+# # parameter controls the timeout on the ip entries. [fast]
+# # If -s is specified the limit is strict, denying browsing
+# # from any further IP addresses until the ttl has expired. Without
+# # -s Squid will just annoy the user by "randomly" denying requests.
+# # (the counter is reset each time the limit is reached and a
+# # request is denied)
+# # NOTE: in acceleration mode or where there is mesh of child proxies,
+# # clients may appear to come from multiple addresses if they are
+# # going through proxy farms, so a limit of 1 may cause user problems.
+#
+# acl aclname req_mime_type [-i] mime-type ...
+# # regex match against the mime type of the request generated
+# # by the client. Can be used to detect file upload or some
+# # types HTTP tunneling requests [fast]
+# # NOTE: This does NOT match the reply. You cannot use this
+# # to match the returned file type.
+#
+# acl aclname req_header header-name [-i] any\.regex\.here
+# # regex match against any of the known request headers. May be
+# # thought of as a superset of "browser", "referer" and "mime-type"
+# # ACL [fast]
+#
+# acl aclname rep_mime_type [-i] mime-type ...
+# # regex match against the mime type of the reply received by
+# # squid. Can be used to detect file download or some
+# # types HTTP tunneling requests. [fast]
+# # NOTE: This has no effect in http_access rules. It only has
+# # effect in rules that affect the reply data stream such as
+# # http_reply_access.
+#
+# acl aclname rep_header header-name [-i] any\.regex\.here
+# # regex match against any of the known reply headers. May be
+# # thought of as a superset of "browser", "referer" and "mime-type"
+# # ACLs [fast]
+#
+# acl aclname external class_name [arguments...]
+# # external ACL lookup via a helper class defined by the
+# # external_acl_type directive [slow]
+#
+# acl aclname user_cert attribute values...
+# # match against attributes in a user SSL certificate
+# # attribute is one of DN/C/O/CN/L/ST [fast]
+#
+# acl aclname ca_cert attribute values...
+# # match against attributes a users issuing CA SSL certificate
+# # attribute is one of DN/C/O/CN/L/ST [fast]
+#
+# acl aclname ext_user username ...
+# acl aclname ext_user_regex [-i] pattern ...
+# # string match on username returned by external acl helper [slow]
+# # use REQUIRED to accept any non-null user name.
+#
+# acl aclname tag tagvalue ...
+# # string match on tag returned by external acl helper [slow]
+#
+# Examples:
+# acl macaddress arp 09:00:2b:23:45:67
+# acl myexample dst_as 1241
+# acl password proxy_auth REQUIRED
+# acl fileupload req_mime_type -i ^multipart/form-data$
+# acl javascript rep_mime_type -i ^application/x-javascript$
+#
+#Default:
+# acl all src all
+#
+#
+# Recommended minimum configuration:
+# (now built-in)
+#acl manager proto cache_object
+#acl localhost src 127.0.0.1/32 ::1
+#acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1
+
+# Example rule allowing access from your local networks.
+# Adapt to list your (internal) IP networks from where browsing
+# should be allowed
+#acl localnet src 10.0.0.0/8 # RFC1918 possible internal network
+#acl localnet src 172.16.0.0/12 # RFC1918 possible internal network
+#acl localnet src 192.168.0.0/16 # RFC1918 possible internal network
+#acl localnet src fc00::/7 # RFC 4193 local private network range
+#acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines
+
+acl SSL_ports port 443
+acl Safe_ports port 80 # http
+acl Safe_ports port 21 # ftp
+acl Safe_ports port 443 # https
+acl Safe_ports port 70 # gopher
+acl Safe_ports port 210 # wais
+acl Safe_ports port 1025-65535 # unregistered ports
+acl Safe_ports port 280 # http-mgmt
+acl Safe_ports port 488 # gss-http
+acl Safe_ports port 591 # filemaker
+acl Safe_ports port 777 # multiling http
+acl CONNECT method CONNECT
+
+# TAG: follow_x_forwarded_for
+# Allowing or Denying the X-Forwarded-For header to be followed to
+# find the original source of a request.
+#
+# Requests may pass through a chain of several other proxies
+# before reaching us. The X-Forwarded-For header will contain a
+# comma-separated list of the IP addresses in the chain, with the
+# rightmost address being the most recent.
+#
+# If a request reaches us from a source that is allowed by this
+# configuration item, then we consult the X-Forwarded-For header
+# to see where that host received the request from. If the
+# X-Forwarded-For header contains multiple addresses, we continue
+# backtracking until we reach an address for which we are not allowed
+# to follow the X-Forwarded-For header, or until we reach the first
+# address in the list. For the purpose of ACL used in the
+# follow_x_forwarded_for directive the src ACL type always matches
+# the address we are testing and srcdomain matches its rDNS.
+#
+# The end result of this process is an IP address that we will
+# refer to as the indirect client address. This address may
+# be treated as the client address for access control, ICAP, delay
+# pools and logging, depending on the acl_uses_indirect_client,
+# icap_uses_indirect_client, delay_pool_uses_indirect_client and
+# log_uses_indirect_client options.
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#
+# SECURITY CONSIDERATIONS:
+#
+# Any host for which we follow the X-Forwarded-For header
+# can place incorrect information in the header, and Squid
+# will use the incorrect information as if it were the
+# source address of the request. This may enable remote
+# hosts to bypass any access control restrictions that are
+# based on the client's source addresses.
+#
+# For example:
+#
+# acl localhost src 127.0.0.1
+# acl my_other_proxy srcdomain .proxy.example.com
+# follow_x_forwarded_for allow localhost
+# follow_x_forwarded_for allow my_other_proxy
+#Default:
+# follow_x_forwarded_for deny all
+
+# TAG: acl_uses_indirect_client on|off
+# Controls whether the indirect client address
+# (see follow_x_forwarded_for) is used instead of the
+# direct client address in acl matching.
+#
+# NOTE: maxconn ACL considers direct TCP links and indirect
+# clients will always have zero. So no match.
+#Default:
+# acl_uses_indirect_client on
+
+# TAG: delay_pool_uses_indirect_client on|off
+# Controls whether the indirect client address
+# (see follow_x_forwarded_for) is used instead of the
+# direct client address in delay pools.
+#Default:
+# delay_pool_uses_indirect_client on
+
+# TAG: log_uses_indirect_client on|off
+# Controls whether the indirect client address
+# (see follow_x_forwarded_for) is used instead of the
+# direct client address in the access log.
+#Default:
+# log_uses_indirect_client on
+
+# TAG: http_access
+# Allowing or Denying access based on defined access lists
+#
+# Access to the HTTP port:
+# http_access allow|deny [!]aclname ...
+#
+# NOTE on default values:
+#
+# If there are no "access" lines present, the default is to deny
+# the request.
+#
+# If none of the "access" lines cause a match, the default is the
+# opposite of the last line in the list. If the last line was
+# deny, the default is allow. Conversely, if the last line
+# is allow, the default will be deny. For these reasons, it is a
+# good idea to have an "deny all" entry at the end of your access
+# lists to avoid potential confusion.
+#
+# This clause supports both fast and slow acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#
+#Default:
+# http_access deny all
+#
+
+#
+# Recommended minimum Access Permission configuration:
+#
+# Only allow cachemgr access from localhost
+http_access allow manager localhost
+http_access deny manager
+
+# Deny requests to certain unsafe ports
+http_access deny !Safe_ports
+
+# Deny CONNECT to other than secure SSL ports
+http_access deny CONNECT !SSL_ports
+
+# We strongly recommend the following be uncommented to protect innocent
+# web applications running on the proxy server who think the only
+# one who can access services on "localhost" is a local user
+#http_access deny to_localhost
+
+#
+# INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS
+#
+
+# Example rule allowing access from your local networks.
+# Adapt localnet in the ACL section to list your (internal) IP networks
+# from where browsing should be allowed
+#http_access allow localnet
+http_access allow localhost
+
+# And finally deny all other access to this proxy
+http_access deny all
+
+# TAG: adapted_http_access
+# Allowing or Denying access based on defined access lists
+#
+# Essentially identical to http_access, but runs after redirectors
+# and ICAP/eCAP adaptation. Allowing access control based on their
+# output.
+#
+# If not set then only http_access is used.
+#Default:
+# none
+
+# TAG: http_reply_access
+# Allow replies to client requests. This is complementary to http_access.
+#
+# http_reply_access allow|deny [!] aclname ...
+#
+# NOTE: if there are no access lines present, the default is to allow
+# all replies
+#
+# If none of the access lines cause a match the opposite of the
+# last line will apply. Thus it is good practice to end the rules
+# with an "allow all" or "deny all" entry.
+#
+# This clause supports both fast and slow acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Default:
+# none
+
+# TAG: icp_access
+# Allowing or Denying access to the ICP port based on defined
+# access lists
+#
+# icp_access allow|deny [!]aclname ...
+#
+# See http_access for details
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#
+## Allow ICP queries from local networks only
+##icp_access allow localnet
+##icp_access deny all
+#Default:
+# icp_access deny all
+
+# TAG: htcp_access
+# Allowing or Denying access to the HTCP port based on defined
+# access lists
+#
+# htcp_access allow|deny [!]aclname ...
+#
+# See http_access for details
+#
+# NOTE: The default if no htcp_access lines are present is to
+# deny all traffic. This default may cause problems with peers
+# using the htcp or htcp-oldsquid options.
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#
+## Allow HTCP queries from local networks only
+##htcp_access allow localnet
+##htcp_access deny all
+#Default:
+# htcp_access deny all
+
+# TAG: htcp_clr_access
+# Allowing or Denying access to purge content using HTCP based
+# on defined access lists
+#
+# htcp_clr_access allow|deny [!]aclname ...
+#
+# See http_access for details
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#
+## Allow HTCP CLR requests from trusted peers
+#acl htcp_clr_peer src 172.16.1.2
+#htcp_clr_access allow htcp_clr_peer
+#Default:
+# htcp_clr_access deny all
+
+# TAG: miss_access
+# Determins whether network access is permitted when satisfying a request.
+#
+# For example;
+# to force your neighbors to use you as a sibling instead of
+# a parent.
+#
+# acl localclients src 172.16.0.0/16
+# miss_access allow localclients
+# miss_access deny !localclients
+#
+# This means only your local clients are allowed to fetch relayed/MISS
+# replies from the network and all other clients can only fetch cached
+# objects (HITs).
+#
+#
+# The default for this setting allows all clients who passed the
+# http_access rules to relay via this proxy.
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Default:
+# miss_access allow all
+
+# TAG: ident_lookup_access
+# A list of ACL elements which, if matched, cause an ident
+# (RFC 931) lookup to be performed for this request. For
+# example, you might choose to always perform ident lookups
+# for your main multi-user Unix boxes, but not for your Macs
+# and PCs. By default, ident lookups are not performed for
+# any requests.
+#
+# To enable ident lookups for specific client addresses, you
+# can follow this example:
+#
+# acl ident_aware_hosts src 198.168.1.0/24
+# ident_lookup_access allow ident_aware_hosts
+# ident_lookup_access deny all
+#
+# Only src type ACL checks are fully supported. A srcdomain
+# ACL might work at times, but it will not always provide
+# the correct result.
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Default:
+# ident_lookup_access deny all
+
+# TAG: reply_body_max_size size [acl acl...]
+# This option specifies the maximum size of a reply body. It can be
+# used to prevent users from downloading very large files, such as
+# MP3's and movies. When the reply headers are received, the
+# reply_body_max_size lines are processed, and the first line where
+# all (if any) listed ACLs are true is used as the maximum body size
+# for this reply.
+#
+# This size is checked twice. First when we get the reply headers,
+# we check the content-length value. If the content length value exists
+# and is larger than the allowed size, the request is denied and the
+# user receives an error message that says "the request or reply
+# is too large." If there is no content-length, and the reply
+# size exceeds this limit, the client's connection is just closed
+# and they will receive a partial reply.
+#
+# WARNING: downstream caches probably can not detect a partial reply
+# if there is no content-length header, so they will cache
+# partial responses and give them out as hits. You should NOT
+# use this option if you have downstream caches.
+#
+# WARNING: A maximum size smaller than the size of squid's error messages
+# will cause an infinite loop and crash squid. Ensure that the smallest
+# non-zero value you use is greater that the maximum header size plus
+# the size of your largest error page.
+#
+# If you set this parameter none (the default), there will be
+# no limit imposed.
+#
+# Configuration Format is:
+# reply_body_max_size SIZE UNITS [acl ...]
+# ie.
+# reply_body_max_size 10 MB
+#
+#Default:
+# none
+
+# NETWORK OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: http_port
+# Usage: port [options]
+# hostname:port [options]
+# 1.2.3.4:port [options]
+#
+# The socket addresses where Squid will listen for HTTP client
+# requests. You may specify multiple socket addresses.
+# There are three forms: port alone, hostname with port, and
+# IP address with port. If you specify a hostname or IP
+# address, Squid binds the socket to that specific
+# address. This replaces the old 'tcp_incoming_address'
+# option. Most likely, you do not need to bind to a specific
+# address, so you can use the port number alone.
+#
+# If you are running Squid in accelerator mode, you
+# probably want to listen on port 80 also, or instead.
+#
+# The -a command line option may be used to specify additional
+# port(s) where Squid listens for proxy request. Such ports will
+# be plain proxy ports with no options.
+#
+# You may specify multiple socket addresses on multiple lines.
+#
+# Options:
+#
+# intercept Support for IP-Layer interception of
+# outgoing requests without browser settings.
+# NP: disables authentication and IPv6 on the port.
+#
+# tproxy Support Linux TPROXY for spoofing outgoing
+# connections using the client IP address.
+# NP: disables authentication and maybe IPv6 on the port.
+#
+# accel Accelerator mode. Also needs at least one of
+# vhost / vport / defaultsite.
+#
+# allow-direct Allow direct forwarding in accelerator mode. Normally
+# accelerated requests are denied direct forwarding as if
+# never_direct was used.
+#
+# defaultsite=domainname
+# What to use for the Host: header if it is not present
+# in a request. Determines what site (not origin server)
+# accelerators should consider the default.
+# Implies accel.
+#
+# vhost Accelerator mode using Host header for virtual domain support.
+# Also uses the port as specified in Host: header unless
+# overridden by the vport option. Implies accel.
+#
+# vport Virtual host port support. Using the http_port number
+# instead of the port passed on Host: headers. Implies accel.
+#
+# vport=NN Virtual host port support. Using the specified port
+# number instead of the port passed on Host: headers.
+# Implies accel.
+#
+# protocol= Protocol to reconstruct accelerated requests with.
+# Defaults to http.
+#
+# ignore-cc Ignore request Cache-Control headers.
+#
+# Warning: This option violates HTTP specifications if
+# used in non-accelerator setups.
+#
+# connection-auth[=on|off]
+# use connection-auth=off to tell Squid to prevent
+# forwarding Microsoft connection oriented authentication
+# (NTLM, Negotiate and Kerberos)
+#
+# disable-pmtu-discovery=
+# Control Path-MTU discovery usage:
+# off lets OS decide on what to do (default).
+# transparent disable PMTU discovery when transparent
+# support is enabled.
+# always disable always PMTU discovery.
+#
+# In many setups of transparently intercepting proxies
+# Path-MTU discovery can not work on traffic towards the
+# clients. This is the case when the intercepting device
+# does not fully track connections and fails to forward
+# ICMP must fragment messages to the cache server. If you
+# have such setup and experience that certain clients
+# sporadically hang or never complete requests set
+# disable-pmtu-discovery option to 'transparent'.
+#
+# ssl-bump Intercept each CONNECT request matching ssl_bump ACL,
+# establish secure connection with the client and with
+# the server, decrypt HTTP messages as they pass through
+# Squid, and treat them as unencrypted HTTP messages,
+# becoming the man-in-the-middle.
+#
+# When this option is enabled, additional options become
+# available to specify SSL-related properties of the
+# client-side connection: cert, key, version, cipher,
+# options, clientca, cafile, capath, crlfile, dhparams,
+# sslflags, and sslcontext. See the https_port directive
+# for more information on these options.
+#
+# The ssl_bump option is required to fully enable
+# the SslBump feature.
+#
+# name= Specifies a internal name for the port. Defaults to
+# the port specification (port or addr:port)
+#
+# tcpkeepalive[=idle,interval,timeout]
+# Enable TCP keepalive probes of idle connections.
+# In seconds; idle is the initial time before TCP starts
+# probing the connection, interval how often to probe, and
+# timeout the time before giving up.
+#
+# If you run Squid on a dual-homed machine with an internal
+# and an external interface we recommend you to specify the
+# internal address:port in http_port. This way Squid will only be
+# visible on the internal address.
+#
+#
+
+# Squid normally listens to port 3128
+http_port 3128
+
+# TAG: https_port
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# Usage: [ip:]port cert=certificate.pem [key=key.pem] [options...]
+#
+# The socket address where Squid will listen for HTTPS client
+# requests.
+#
+# This is really only useful for situations where you are running
+# squid in accelerator mode and you want to do the SSL work at the
+# accelerator level.
+#
+# You may specify multiple socket addresses on multiple lines,
+# each with their own SSL certificate and/or options.
+#
+# Options:
+#
+# accel Accelerator mode. Also needs at least one of
+# defaultsite or vhost.
+#
+# defaultsite= The name of the https site presented on
+# this port. Implies accel.
+#
+# vhost Accelerator mode using Host header for virtual
+# domain support. Requires a wildcard certificate
+# or other certificate valid for more than one domain.
+# Implies accel.
+#
+# protocol= Protocol to reconstruct accelerated requests with.
+# Defaults to https.
+#
+# cert= Path to SSL certificate (PEM format).
+#
+# key= Path to SSL private key file (PEM format)
+# if not specified, the certificate file is
+# assumed to be a combined certificate and
+# key file.
+#
+# version= The version of SSL/TLS supported
+# 1 automatic (default)
+# 2 SSLv2 only
+# 3 SSLv3 only
+# 4 TLSv1 only
+#
+# cipher= Colon separated list of supported ciphers.
+# NOTE: some ciphers such as EDH ciphers depend on
+# additional settings. If those settings are
+# omitted the ciphers may be silently ignored
+# by the OpenSSL library.
+#
+# options= Various SSL engine options. The most important
+# being:
+# NO_SSLv2 Disallow the use of SSLv2
+# NO_SSLv3 Disallow the use of SSLv3
+# NO_TLSv1 Disallow the use of TLSv1
+# SINGLE_DH_USE Always create a new key when using
+# temporary/ephemeral DH key exchanges
+# See OpenSSL SSL_CTX_set_options documentation for a
+# complete list of options.
+#
+# clientca= File containing the list of CAs to use when
+# requesting a client certificate.
+#
+# cafile= File containing additional CA certificates to
+# use when verifying client certificates. If unset
+# clientca will be used.
+#
+# capath= Directory containing additional CA certificates
+# and CRL lists to use when verifying client certificates.
+#
+# crlfile= File of additional CRL lists to use when verifying
+# the client certificate, in addition to CRLs stored in
+# the capath. Implies VERIFY_CRL flag below.
+#
+# dhparams= File containing DH parameters for temporary/ephemeral
+# DH key exchanges. See OpenSSL documentation for details
+# on how to create this file.
+# WARNING: EDH ciphers will be silently disabled if this
+# option is not set.
+#
+# sslflags= Various flags modifying the use of SSL:
+# DELAYED_AUTH
+# Don't request client certificates
+# immediately, but wait until acl processing
+# requires a certificate (not yet implemented).
+# NO_DEFAULT_CA
+# Don't use the default CA lists built in
+# to OpenSSL.
+# NO_SESSION_REUSE
+# Don't allow for session reuse. Each connection
+# will result in a new SSL session.
+# VERIFY_CRL
+# Verify CRL lists when accepting client
+# certificates.
+# VERIFY_CRL_ALL
+# Verify CRL lists for all certificates in the
+# client certificate chain.
+#
+# sslcontext= SSL session ID context identifier.
+#
+# generate-host-certificates[=<on|off>]
+# Dynamically create SSL server certificates for the
+# destination hosts of bumped CONNECT requests.When
+# enabled, the cert and key options are used to sign
+# generated certificates. Otherwise generated
+# certificate will be selfsigned.
+# If there is CA certificate life time of generated
+# certificate equals lifetime of CA certificate. If
+# generated certificate is selfsigned lifetime is three
+# years.
+# This option is enabled by default when SslBump is used.
+# See the sslBump option above for more information.
+#
+# dynamic_cert_mem_cache_size=SIZE
+# Approximate total RAM size spent on cached generated
+# certificates. If set to zero, caching is disabled. The
+# default value is 4MB. An average XXX-bit certificate
+# consumes about XXX bytes of RAM.
+#
+# vport Accelerator with IP based virtual host support.
+#
+# vport=NN As above, but uses specified port number rather
+# than the https_port number. Implies accel.
+#
+# name= Specifies a internal name for the port. Defaults to
+# the port specification (port or addr:port)
+#
+#Default:
+# none
+
+# TAG: tcp_outgoing_tos
+# Allows you to select a TOS/Diffserv value to mark outgoing
+# connections with, based on the username or source address
+# making the request.
+#
+# tcp_outgoing_tos ds-field [!]aclname ...
+#
+# Example where normal_service_net uses the TOS value 0x00
+# and good_service_net uses 0x20
+#
+# acl normal_service_net src 10.0.0.0/24
+# acl good_service_net src 10.0.1.0/24
+# tcp_outgoing_tos 0x00 normal_service_net
+# tcp_outgoing_tos 0x20 good_service_net
+#
+# TOS/DSCP values really only have local significance - so you should
+# know what you're specifying. For more information, see RFC2474,
+# RFC2475, and RFC3260.
+#
+# The TOS/DSCP byte must be exactly that - a octet value 0 - 255, or
+# "default" to use whatever default your host has. Note that in
+# practice often only multiples of 4 is usable as the two rightmost bits
+# have been redefined for use by ECN (RFC 3168 section 23.1).
+#
+# Processing proceeds in the order specified, and stops at first fully
+# matching line.
+#
+# Note: The use of this directive using client dependent ACLs is
+# incompatible with the use of server side persistent connections. To
+# ensure correct results it is best to set server_persistent_connections
+# to off when using this directive in such configurations.
+#Default:
+# none
+
+# TAG: clientside_tos
+# Allows you to select a TOS/Diffserv value to mark client-side
+# connections with, based on the username or source address
+# making the request.
+#Default:
+# none
+
+# TAG: qos_flows
+# Allows you to select a TOS/DSCP value to mark outgoing
+# connections with, based on where the reply was sourced.
+#
+# TOS values really only have local significance - so you should
+# know what you're specifying. For more information, see RFC2474,
+# RFC2475, and RFC3260.
+#
+# The TOS/DSCP byte must be exactly that - octet value 0x00-0xFF.
+# Note that in practice often only values up to 0x3F are usable
+# as the two highest bits have been redefined for use by ECN
+# (RFC3168).
+#
+# This setting is configured by setting the source TOS values:
+#
+# local-hit=0xFF Value to mark local cache hits.
+#
+# sibling-hit=0xFF Value to mark hits from sibling peers.
+#
+# parent-hit=0xFF Value to mark hits from parent peers.
+#
+#
+# NOTE: 'miss' preserve feature is only possible on Linux at this time.
+#
+# For the following to work correctly, you will need to patch your
+# linux kernel with the TOS preserving ZPH patch.
+# The kernel patch can be downloaded from http://zph.bratcheda.org
+#
+# disable-preserve-miss
+# By default, the existing TOS value of the response coming
+# from the remote server will be retained and masked with
+# miss-mark. This option disables that feature.
+#
+# miss-mask=0xFF
+# Allows you to mask certain bits in the TOS received from the
+# remote server, before copying the value to the TOS sent
+# towards clients.
+# Default: 0xFF (TOS from server is not changed).
+#
+#Default:
+# none
+
+# TAG: tcp_outgoing_address
+# Allows you to map requests to different outgoing IP addresses
+# based on the username or source address of the user making
+# the request.
+#
+# tcp_outgoing_address ipaddr [[!]aclname] ...
+#
+# Example where requests from 10.0.0.0/24 will be forwarded
+# with source address 10.1.0.1, 10.0.2.0/24 forwarded with
+# source address 10.1.0.2 and the rest will be forwarded with
+# source address 10.1.0.3.
+#
+# acl normal_service_net src 10.0.0.0/24
+# acl good_service_net src 10.0.2.0/24
+# tcp_outgoing_address 10.1.0.1 normal_service_net
+# tcp_outgoing_address 10.1.0.2 good_service_net
+# tcp_outgoing_address 10.1.0.3
+#
+# Processing proceeds in the order specified, and stops at first fully
+# matching line.
+#
+# Note: The use of this directive using client dependent ACLs is
+# incompatible with the use of server side persistent connections. To
+# ensure correct results it is best to set server_persistent_connections
+# to off when using this directive in such configurations.
+#
+#
+# IPv6 Magic:
+#
+# Squid is built with a capability of bridging the IPv4 and IPv6
+# internets.
+# tcp_outgoing_address as exampled above breaks this bridging by forcing
+# all outbound traffic through a certain IPv4 which may be on the wrong
+# side of the IPv4/IPv6 boundary.
+#
+# To operate with tcp_outgoing_address and keep the bridging benefits
+# an additional ACL needs to be used which ensures the IPv6-bound traffic
+# is never forced or permitted out the IPv4 interface.
+#
+# # IPv6 destination test along with a dummy access control to perform the required DNS
+# # This MUST be place before any ALLOW rules.
+# acl to_ipv6 dst ipv6
+# http_access deny ipv6 !all
+#
+# tcp_outgoing_address 2001:db8::c001 good_service_net to_ipv6
+# tcp_outgoing_address 10.1.0.2 good_service_net !to_ipv6
+#
+# tcp_outgoing_address 2001:db8::beef normal_service_net to_ipv6
+# tcp_outgoing_address 10.1.0.1 normal_service_net !to_ipv6
+#
+# tcp_outgoing_address 2001:db8::1 to_ipv6
+# tcp_outgoing_address 10.1.0.3 !to_ipv6
+#
+# WARNING:
+# 'dst ipv6' bases its selection assuming DIRECT access.
+# If peers are used the peername ACL are needed to select outgoing
+# address which can link to the peer.
+#
+# 'dst ipv6' is a slow ACL. It will only work here if 'dst' is used
+# previously in the http_access rules to locate the destination IP.
+# Some more magic may be needed for that:
+# http_access allow to_ipv6 !all
+# (meaning, allow if to IPv6 but not from anywhere ;)
+#
+#Default:
+# none
+
+# SSL OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: ssl_unclean_shutdown
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# Some browsers (especially MSIE) bugs out on SSL shutdown
+# messages.
+#Default:
+# ssl_unclean_shutdown off
+
+# TAG: ssl_engine
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# The OpenSSL engine to use. You will need to set this if you
+# would like to use hardware SSL acceleration for example.
+#Default:
+# none
+
+# TAG: sslproxy_client_certificate
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# Client SSL Certificate to use when proxying https:// URLs
+#Default:
+# none
+
+# TAG: sslproxy_client_key
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# Client SSL Key to use when proxying https:// URLs
+#Default:
+# none
+
+# TAG: sslproxy_version
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# SSL version level to use when proxying https:// URLs
+#Default:
+# sslproxy_version 1
+
+# TAG: sslproxy_options
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# SSL engine options to use when proxying https:// URLs
+#
+# The most important being:
+#
+# NO_SSLv2 Disallow the use of SSLv2
+# NO_SSLv3 Disallow the use of SSLv3
+# NO_TLSv1 Disallow the use of TLSv1
+# SINGLE_DH_USE
+# Always create a new key when using
+# temporary/ephemeral DH key exchanges
+#
+# These options vary depending on your SSL engine.
+# See the OpenSSL SSL_CTX_set_options documentation for a
+# complete list of possible options.
+#Default:
+# none
+
+# TAG: sslproxy_cipher
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# SSL cipher list to use when proxying https:// URLs
+#
+# Colon separated list of supported ciphers.
+#Default:
+# none
+
+# TAG: sslproxy_cafile
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# file containing CA certificates to use when verifying server
+# certificates while proxying https:// URLs
+#Default:
+# none
+
+# TAG: sslproxy_capath
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# directory containing CA certificates to use when verifying
+# server certificates while proxying https:// URLs
+#Default:
+# none
+
+# TAG: ssl_bump
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# This ACL controls which CONNECT requests to an http_port
+# marked with an sslBump flag are actually "bumped". Please
+# see the sslBump flag of an http_port option for more details
+# about decoding proxied SSL connections.
+#
+# By default, no requests are bumped.
+#
+# See also: http_port ssl-bump
+#
+# This clause supports both fast and slow acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#
+#
+# # Example: Bump all requests except those originating from localhost and
+# # those going to webax.com or example.com sites.
+#
+# acl localhost src 127.0.0.1/32
+# acl broken_sites dstdomain .webax.com
+# acl broken_sites dstdomain .example.com
+# ssl_bump deny localhost
+# ssl_bump deny broken_sites
+# ssl_bump allow all
+#Default:
+# none
+
+# TAG: sslproxy_flags
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# Various flags modifying the use of SSL while proxying https:// URLs:
+# DONT_VERIFY_PEER Accept certificates that fail verification.
+# For refined control, see sslproxy_cert_error.
+# NO_DEFAULT_CA Don't use the default CA list built in
+# to OpenSSL.
+#Default:
+# none
+
+# TAG: sslproxy_cert_error
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# Use this ACL to bypass server certificate validation errors.
+#
+# For example, the following lines will bypass all validation errors
+# when talking to servers located at 172.16.0.0/16. All other
+# validation errors will result in ERR_SECURE_CONNECT_FAIL error.
+#
+# acl BrokenServersAtTrustedIP dst 172.16.0.0/16
+# sslproxy_cert_error allow BrokenServersAtTrustedIP
+# sslproxy_cert_error deny all
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+# Using slow acl types may result in server crashes
+#
+# Without this option, all server certificate validation errors
+# terminate the transaction. Bypassing validation errors is dangerous
+# because an error usually implies that the server cannot be trusted and
+# the connection may be insecure.
+#
+# See also: sslproxy_flags and DONT_VERIFY_PEER.
+#
+# Default setting: sslproxy_cert_error deny all
+#Default:
+# none
+
+# TAG: sslpassword_program
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ssl option
+#
+# Specify a program used for entering SSL key passphrases
+# when using encrypted SSL certificate keys. If not specified
+# keys must either be unencrypted, or Squid started with the -N
+# option to allow it to query interactively for the passphrase.
+#
+# The key file name is given as argument to the program allowing
+# selection of the right password if you have multiple encrypted
+# keys.
+#Default:
+# none
+
+#OPTIONS RELATING TO EXTERNAL SSL_CRTD
+#-----------------------------------------------------------------------------
+
+# TAG: sslcrtd_program
+# Note: This option is only available if Squid is rebuilt with the
+# -DUSE_SSL_CRTD define
+#
+# Specify the location and options of the executable for ssl_crtd process.
+# /usr/lib/squid3/ssl_crtd program requires -s and -M parameters
+# For more information use:
+# /usr/lib/squid3/ssl_crtd -h
+#Default:
+# sslcrtd_program /usr/lib/squid3/ssl_crtd -s /var/lib/ssl_db -M 4MB
+
+# TAG: sslcrtd_children
+# Note: This option is only available if Squid is rebuilt with the
+# -DUSE_SSL_CRTD define
+#
+# The maximum number of processes spawn to service ssl server.
+# The maximum this may be safely set to is 32.
+#
+# You must have at least one ssl_crtd process.
+#Default:
+# sslcrtd_children 5
+
+# OPTIONS WHICH AFFECT THE NEIGHBOR SELECTION ALGORITHM
+# -----------------------------------------------------------------------------
+
+# TAG: cache_peer
+# To specify other caches in a hierarchy, use the format:
+#
+# cache_peer hostname type http-port icp-port [options]
+#
+# For example,
+#
+# # proxy icp
+# # hostname type port port options
+# # -------------------- -------- ----- ----- -----------
+# cache_peer parent.foo.net parent 3128 3130 default
+# cache_peer sib1.foo.net sibling 3128 3130 proxy-only
+# cache_peer sib2.foo.net sibling 3128 3130 proxy-only
+# cache_peer example.com parent 80 0 default
+# cache_peer cdn.example.com sibling 3128 0
+#
+# type: either 'parent', 'sibling', or 'multicast'.
+#
+# proxy-port: The port number where the peer accept HTTP requests.
+# For other Squid proxies this is usually 3128
+# For web servers this is usually 80
+#
+# icp-port: Used for querying neighbor caches about objects.
+# Set to 0 if the peer does not support ICP or HTCP.
+# See ICP and HTCP options below for additional details.
+#
+#
+# ==== ICP OPTIONS ====
+#
+# You MUST also set icp_port and icp_access explicitly when using these options.
+# The defaults will prevent peer traffic using ICP.
+#
+#
+# no-query Disable ICP queries to this neighbor.
+#
+# multicast-responder
+# Indicates the named peer is a member of a multicast group.
+# ICP queries will not be sent directly to the peer, but ICP
+# replies will be accepted from it.
+#
+# closest-only Indicates that, for ICP_OP_MISS replies, we'll only forward
+# CLOSEST_PARENT_MISSes and never FIRST_PARENT_MISSes.
+#
+# background-ping
+# To only send ICP queries to this neighbor infrequently.
+# This is used to keep the neighbor round trip time updated
+# and is usually used in conjunction with weighted-round-robin.
+#
+#
+# ==== HTCP OPTIONS ====
+#
+# You MUST also set htcp_port and htcp_access explicitly when using these options.
+# The defaults will prevent peer traffic using HTCP.
+#
+#
+# htcp Send HTCP, instead of ICP, queries to the neighbor.
+# You probably also want to set the "icp-port" to 4827
+# instead of 3130.
+#
+# htcp-oldsquid Send HTCP to old Squid versions.
+#
+# htcp-no-clr Send HTCP to the neighbor but without
+# sending any CLR requests. This cannot be used with
+# htcp-only-clr.
+#
+# htcp-only-clr Send HTCP to the neighbor but ONLY CLR requests.
+# This cannot be used with htcp-no-clr.
+#
+# htcp-no-purge-clr
+# Send HTCP to the neighbor including CLRs but only when
+# they do not result from PURGE requests.
+#
+# htcp-forward-clr
+# Forward any HTCP CLR requests this proxy receives to the peer.
+#
+#
+# ==== PEER SELECTION METHODS ====
+#
+# The default peer selection method is ICP, with the first responding peer
+# being used as source. These options can be used for better load balancing.
+#
+#
+# default This is a parent cache which can be used as a "last-resort"
+# if a peer cannot be located by any of the peer-selection methods.
+# If specified more than once, only the first is used.
+#
+# round-robin Load-Balance parents which should be used in a round-robin
+# fashion in the absence of any ICP queries.
+# weight=N can be used to add bias.
+#
+# weighted-round-robin
+# Load-Balance parents which should be used in a round-robin
+# fashion with the frequency of each parent being based on the
+# round trip time. Closer parents are used more often.
+# Usually used for background-ping parents.
+# weight=N can be used to add bias.
+#
+# carp Load-Balance parents which should be used as a CARP array.
+# The requests will be distributed among the parents based on the
+# CARP load balancing hash function based on their weight.
+#
+# userhash Load-balance parents based on the client proxy_auth or ident username.
+#
+# sourcehash Load-balance parents based on the client source IP.
+#
+# multicast-siblings
+# To be used only for cache peers of type "multicast".
+# ALL members of this multicast group have "sibling"
+# relationship with it, not "parent". This is to a multicast
+# group when the requested object would be fetched only from
+# a "parent" cache, anyway. It's useful, e.g., when
+# configuring a pool of redundant Squid proxies, being
+# members of the same multicast group.
+#
+#
+# ==== PEER SELECTION OPTIONS ====
+#
+# weight=N use to affect the selection of a peer during any weighted
+# peer-selection mechanisms.
+# The weight must be an integer; default is 1,
+# larger weights are favored more.
+# This option does not affect parent selection if a peering
+# protocol is not in use.
+#
+# basetime=N Specify a base amount to be subtracted from round trip
+# times of parents.
+# It is subtracted before division by weight in calculating
+# which parent to fectch from. If the rtt is less than the
+# base time the rtt is set to a minimal value.
+#
+# ttl=N Specify a TTL to use when sending multicast ICP queries
+# to this address.
+# Only useful when sending to a multicast group.
+# Because we don't accept ICP replies from random
+# hosts, you must configure other group members as
+# peers with the 'multicast-responder' option.
+#
+# no-delay To prevent access to this neighbor from influencing the
+# delay pools.
+#
+# digest-url=URL Tell Squid to fetch the cache digest (if digests are
+# enabled) for this host from the specified URL rather
+# than the Squid default location.
+#
+#
+# ==== ACCELERATOR / REVERSE-PROXY OPTIONS ====
+#
+# originserver Causes this parent to be contacted as an origin server.
+# Meant to be used in accelerator setups when the peer
+# is a web server.
+#
+# forceddomain=name
+# Set the Host header of requests forwarded to this peer.
+# Useful in accelerator setups where the server (peer)
+# expects a certain domain name but clients may request
+# others. ie example.com or www.example.com
+#
+# no-digest Disable request of cache digests.
+#
+# no-netdb-exchange
+# Disables requesting ICMP RTT database (NetDB).
+#
+#
+# ==== AUTHENTICATION OPTIONS ====
+#
+# login=user:password
+# If this is a personal/workgroup proxy and your parent
+# requires proxy authentication.
+#
+# Note: The string can include URL escapes (i.e. %20 for
+# spaces). This also means % must be written as %%.
+#
+# login=PROXYPASS
+# Send login details received from client to this peer.
+# Authentication is not required, nor changed.
+#
+# Note: This will pass any form of authentication but
+# only Basic auth will work through a proxy unless the
+# connection-auth options are also used.
+#
+# login=PASS Send login details received from client to this peer.
+# Authentication is not required by this option.
+# If there are no client-provided authentication headers
+# to pass on, but username and password are available
+# from either proxy login or an external ACL user= and
+# password= result tags they may be sent instead.
+#
+# Note: To combine this with proxy_auth both proxies must
+# share the same user database as HTTP only allows for
+# a single login (one for proxy, one for origin server).
+# Also be warned this will expose your users proxy
+# password to the peer. USE WITH CAUTION
+#
+# login=*:password
+# Send the username to the upstream cache, but with a
+# fixed password. This is meant to be used when the peer
+# is in another administrative domain, but it is still
+# needed to identify each user.
+# The star can optionally be followed by some extra
+# information which is added to the username. This can
+# be used to identify this proxy to the peer, similar to
+# the login=username:password option above.
+#
+# connection-auth=on|off
+# Tell Squid that this peer does or not support Microsoft
+# connection oriented authentication, and any such
+# challenges received from there should be ignored.
+# Default is auto to automatically determine the status
+# of the peer.
+#
+#
+# ==== SSL / HTTPS / TLS OPTIONS ====
+#
+# ssl Encrypt connections to this peer with SSL/TLS.
+#
+# sslcert=/path/to/ssl/certificate
+# A client SSL certificate to use when connecting to
+# this peer.
+#
+# sslkey=/path/to/ssl/key
+# The private SSL key corresponding to sslcert above.
+# If 'sslkey' is not specified 'sslcert' is assumed to
+# reference a combined file containing both the
+# certificate and the key.
+#
+# sslversion=1|2|3|4
+# The SSL version to use when connecting to this peer
+# 1 = automatic (default)
+# 2 = SSL v2 only
+# 3 = SSL v3 only
+# 4 = TLS v1 only
+#
+# sslcipher=... The list of valid SSL ciphers to use when connecting
+# to this peer.
+#
+# ssloptions=... Specify various SSL engine options:
+# NO_SSLv2 Disallow the use of SSLv2
+# NO_SSLv3 Disallow the use of SSLv3
+# NO_TLSv1 Disallow the use of TLSv1
+# See src/ssl_support.c or the OpenSSL documentation for
+# a more complete list.
+#
+# sslcafile=... A file containing additional CA certificates to use
+# when verifying the peer certificate.
+#
+# sslcapath=... A directory containing additional CA certificates to
+# use when verifying the peer certificate.
+#
+# sslcrlfile=... A certificate revocation list file to use when
+# verifying the peer certificate.
+#
+# sslflags=... Specify various flags modifying the SSL implementation:
+#
+# DONT_VERIFY_PEER
+# Accept certificates even if they fail to
+# verify.
+# NO_DEFAULT_CA
+# Don't use the default CA list built in
+# to OpenSSL.
+# DONT_VERIFY_DOMAIN
+# Don't verify the peer certificate
+# matches the server name
+#
+# ssldomain= The peer name as advertised in it's certificate.
+# Used for verifying the correctness of the received peer
+# certificate. If not specified the peer hostname will be
+# used.
+#
+# front-end-https
+# Enable the "Front-End-Https: On" header needed when
+# using Squid as a SSL frontend in front of Microsoft OWA.
+# See MS KB document Q307347 for details on this header.
+# If set to auto the header will only be added if the
+# request is forwarded as a https:// URL.
+#
+#
+# ==== GENERAL OPTIONS ====
+#
+# connect-timeout=N
+# A peer-specific connect timeout.
+# Also see the peer_connect_timeout directive.
+#
+# connect-fail-limit=N
+# How many times connecting to a peer must fail before
+# it is marked as down. Default is 10.
+#
+# allow-miss Disable Squid's use of only-if-cached when forwarding
+# requests to siblings. This is primarily useful when
+# icp_hit_stale is used by the sibling. To extensive use
+# of this option may result in forwarding loops, and you
+# should avoid having two-way peerings with this option.
+# For example to deny peer usage on requests from peer
+# by denying cache_peer_access if the source is a peer.
+#
+# max-conn=N Limit the amount of connections Squid may open to this
+# peer. see also
+#
+# name=xxx Unique name for the peer.
+# Required if you have multiple peers on the same host
+# but different ports.
+# This name can be used in cache_peer_access and similar
+# directives to dentify the peer.
+# Can be used by outgoing access controls through the
+# peername ACL type.
+#
+# no-tproxy Do not use the client-spoof TPROXY support when forwarding
+# requests to this peer. Use normal address selection instead.
+#
+# proxy-only objects fetched from the peer will not be stored locally.
+#
+#Default:
+# none
+
+# TAG: cache_peer_domain
+# Use to limit the domains for which a neighbor cache will be
+# queried. Usage:
+#
+# cache_peer_domain cache-host domain [domain ...]
+# cache_peer_domain cache-host !domain
+#
+# For example, specifying
+#
+# cache_peer_domain parent.foo.net .edu
+#
+# has the effect such that UDP query packets are sent to
+# 'bigserver' only when the requested object exists on a
+# server in the .edu domain. Prefixing the domainname
+# with '!' means the cache will be queried for objects
+# NOT in that domain.
+#
+# NOTE: * Any number of domains may be given for a cache-host,
+# either on the same or separate lines.
+# * When multiple domains are given for a particular
+# cache-host, the first matched domain is applied.
+# * Cache hosts with no domain restrictions are queried
+# for all requests.
+# * There are no defaults.
+# * There is also a 'cache_peer_access' tag in the ACL
+# section.
+#Default:
+# none
+
+# TAG: cache_peer_access
+# Similar to 'cache_peer_domain' but provides more flexibility by
+# using ACL elements.
+#
+# cache_peer_access cache-host allow|deny [!]aclname ...
+#
+# The syntax is identical to 'http_access' and the other lists of
+# ACL elements. See the comments for 'http_access' below, or
+# the Squid FAQ (http://wiki.squid-cache.org/SquidFaq/SquidAcl).
+#Default:
+# none
+
+# TAG: neighbor_type_domain
+# usage: neighbor_type_domain neighbor parent|sibling domain domain ...
+#
+# Modifying the neighbor type for specific domains is now
+# possible. You can treat some domains differently than the the
+# default neighbor type specified on the 'cache_peer' line.
+# Normally it should only be necessary to list domains which
+# should be treated differently because the default neighbor type
+# applies for hostnames which do not match domains listed here.
+#
+#EXAMPLE:
+# cache_peer cache.foo.org parent 3128 3130
+# neighbor_type_domain cache.foo.org sibling .com .net
+# neighbor_type_domain cache.foo.org sibling .au .de
+#Default:
+# none
+
+# TAG: dead_peer_timeout (seconds)
+# This controls how long Squid waits to declare a peer cache
+# as "dead." If there are no ICP replies received in this
+# amount of time, Squid will declare the peer dead and not
+# expect to receive any further ICP replies. However, it
+# continues to send ICP queries, and will mark the peer as
+# alive upon receipt of the first subsequent ICP reply.
+#
+# This timeout also affects when Squid expects to receive ICP
+# replies from peers. If more than 'dead_peer' seconds have
+# passed since the last ICP reply was received, Squid will not
+# expect to receive an ICP reply on the next query. Thus, if
+# your time between requests is greater than this timeout, you
+# will see a lot of requests sent DIRECT to origin servers
+# instead of to your parents.
+#Default:
+# dead_peer_timeout 10 seconds
+
+# TAG: forward_max_tries
+# Controls how many different forward paths Squid will try
+# before giving up. See also forward_timeout.
+#Default:
+# forward_max_tries 10
+
+# TAG: hierarchy_stoplist
+# A list of words which, if found in a URL, cause the object to
+# be handled directly by this cache. In other words, use this
+# to not query neighbor caches for certain objects. You may
+# list this option multiple times.
+#
+# Example:
+# hierarchy_stoplist cgi-bin ?
+#
+# Note: never_direct overrides this option.
+#Default:
+# none
+
+# MEMORY CACHE OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: cache_mem (bytes)
+# NOTE: THIS PARAMETER DOES NOT SPECIFY THE MAXIMUM PROCESS SIZE.
+# IT ONLY PLACES A LIMIT ON HOW MUCH ADDITIONAL MEMORY SQUID WILL
+# USE AS A MEMORY CACHE OF OBJECTS. SQUID USES MEMORY FOR OTHER
+# THINGS AS WELL. SEE THE SQUID FAQ SECTION 8 FOR DETAILS.
+#
+# 'cache_mem' specifies the ideal amount of memory to be used
+# for:
+# * In-Transit objects
+# * Hot Objects
+# * Negative-Cached objects
+#
+# Data for these objects are stored in 4 KB blocks. This
+# parameter specifies the ideal upper limit on the total size of
+# 4 KB blocks allocated. In-Transit objects take the highest
+# priority.
+#
+# In-transit objects have priority over the others. When
+# additional space is needed for incoming data, negative-cached
+# and hot objects will be released. In other words, the
+# negative-cached and hot objects will fill up any unused space
+# not needed for in-transit objects.
+#
+# If circumstances require, this limit will be exceeded.
+# Specifically, if your incoming request rate requires more than
+# 'cache_mem' of memory to hold in-transit objects, Squid will
+# exceed this limit to satisfy the new requests. When the load
+# decreases, blocks will be freed until the high-water mark is
+# reached. Thereafter, blocks will be used to store hot
+# objects.
+#Default:
+# cache_mem 256 MB
+
+# TAG: maximum_object_size_in_memory (bytes)
+# Objects greater than this size will not be attempted to kept in
+# the memory cache. This should be set high enough to keep objects
+# accessed frequently in memory to improve performance whilst low
+# enough to keep larger objects from hoarding cache_mem.
+#Default:
+# maximum_object_size_in_memory 512 KB
+
+# TAG: memory_replacement_policy
+# The memory replacement policy parameter determines which
+# objects are purged from memory when memory space is needed.
+#
+# See cache_replacement_policy for details.
+#Default:
+# memory_replacement_policy lru
+
+# DISK CACHE OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: cache_replacement_policy
+# The cache replacement policy parameter determines which
+# objects are evicted (replaced) when disk space is needed.
+#
+# lru : Squid's original list based LRU policy
+# heap GDSF : Greedy-Dual Size Frequency
+# heap LFUDA: Least Frequently Used with Dynamic Aging
+# heap LRU : LRU policy implemented using a heap
+#
+# Applies to any cache_dir lines listed below this.
+#
+# The LRU policies keeps recently referenced objects.
+#
+# The heap GDSF policy optimizes object hit rate by keeping smaller
+# popular objects in cache so it has a better chance of getting a
+# hit. It achieves a lower byte hit rate than LFUDA though since
+# it evicts larger (possibly popular) objects.
+#
+# The heap LFUDA policy keeps popular objects in cache regardless of
+# their size and thus optimizes byte hit rate at the expense of
+# hit rate since one large, popular object will prevent many
+# smaller, slightly less popular objects from being cached.
+#
+# Both policies utilize a dynamic aging mechanism that prevents
+# cache pollution that can otherwise occur with frequency-based
+# replacement policies.
+#
+# NOTE: if using the LFUDA replacement policy you should increase
+# the value of maximum_object_size above its default of 4096 KB to
+# to maximize the potential byte hit rate improvement of LFUDA.
+#
+# For more information about the GDSF and LFUDA cache replacement
+# policies see http://www.hpl.hp.com/techreports/1999/HPL-1999-69.html
+# and http://fog.hpl.external.hp.com/techreports/98/HPL-98-173.html.
+#Default:
+# cache_replacement_policy lru
+
+# TAG: cache_dir
+# Usage:
+#
+# cache_dir Type Directory-Name Fs-specific-data [options]
+#
+# You can specify multiple cache_dir lines to spread the
+# cache among different disk partitions.
+#
+# Type specifies the kind of storage system to use. Only "ufs"
+# is built by default. To enable any of the other storage systems
+# see the --enable-storeio configure option.
+#
+# 'Directory' is a top-level directory where cache swap
+# files will be stored. If you want to use an entire disk
+# for caching, this can be the mount-point directory.
+# The directory must exist and be writable by the Squid
+# process. Squid will NOT create this directory for you.
+#
+# The ufs store type:
+#
+# "ufs" is the old well-known Squid storage format that has always
+# been there.
+#
+# cache_dir ufs Directory-Name Mbytes L1 L2 [options]
+#
+# 'Mbytes' is the amount of disk space (MB) to use under this
+# directory. The default is 100 MB. Change this to suit your
+# configuration. Do NOT put the size of your disk drive here.
+# Instead, if you want Squid to use the entire disk drive,
+# subtract 20% and use that value.
+#
+# 'L1' is the number of first-level subdirectories which
+# will be created under the 'Directory'. The default is 16.
+#
+# 'L2' is the number of second-level subdirectories which
+# will be created under each first-level directory. The default
+# is 256.
+#
+# The aufs store type:
+#
+# "aufs" uses the same storage format as "ufs", utilizing
+# POSIX-threads to avoid blocking the main Squid process on
+# disk-I/O. This was formerly known in Squid as async-io.
+#
+# cache_dir aufs Directory-Name Mbytes L1 L2 [options]
+#
+# see argument descriptions under ufs above
+#
+# The diskd store type:
+#
+# "diskd" uses the same storage format as "ufs", utilizing a
+# separate process to avoid blocking the main Squid process on
+# disk-I/O.
+#
+# cache_dir diskd Directory-Name Mbytes L1 L2 [options] [Q1=n] [Q2=n]
+#
+# see argument descriptions under ufs above
+#
+# Q1 specifies the number of unacknowledged I/O requests when Squid
+# stops opening new files. If this many messages are in the queues,
+# Squid won't open new files. Default is 64
+#
+# Q2 specifies the number of unacknowledged messages when Squid
+# starts blocking. If this many messages are in the queues,
+# Squid blocks until it receives some replies. Default is 72
+#
+# When Q1 < Q2 (the default), the cache directory is optimized
+# for lower response time at the expense of a decrease in hit
+# ratio. If Q1 > Q2, the cache directory is optimized for
+# higher hit ratio at the expense of an increase in response
+# time.
+#
+# The coss store type:
+#
+# NP: COSS filesystem in Squid-3 has been deemed too unstable for
+# production use and has thus been removed from this release.
+# We hope that it can be made usable again soon.
+#
+# block-size=n defines the "block size" for COSS cache_dir's.
+# Squid uses file numbers as block numbers. Since file numbers
+# are limited to 24 bits, the block size determines the maximum
+# size of the COSS partition. The default is 512 bytes, which
+# leads to a maximum cache_dir size of 512<<24, or 8 GB. Note
+# you should not change the coss block size after Squid
+# has written some objects to the cache_dir.
+#
+# The coss file store has changed from 2.5. Now it uses a file
+# called 'stripe' in the directory names in the config - and
+# this will be created by squid -z.
+#
+# Common options:
+#
+# no-store, no new objects should be stored to this cache_dir
+#
+# max-size=n, refers to the max object size in bytes this cache_dir
+# supports. It is used to select the cache_dir to store the object.
+# Note: To make optimal use of the max-size limits you should order
+# the cache_dir lines with the smallest max-size value first and the
+# ones with no max-size specification last.
+#
+# Note for coss, max-size must be less than COSS_MEMBUF_SZ,
+# which can be changed with the --with-coss-membuf-size=N configure
+# option.
+#
+
+# Uncomment and adjust the following to add a disk cache directory.
+#cache_dir ufs /var/spool/squid3 100 16 256
+cache_dir ufs /var/spool/squid3 8192 16 1024
+
+# TAG: store_dir_select_algorithm
+# Set this to 'round-robin' as an alternative.
+#Default:
+# store_dir_select_algorithm least-load
+
+# TAG: max_open_disk_fds
+# To avoid having disk as the I/O bottleneck Squid can optionally
+# bypass the on-disk cache if more than this amount of disk file
+# descriptors are open.
+#
+# A value of 0 indicates no limit.
+#Default:
+# max_open_disk_fds 0
+
+# TAG: minimum_object_size (bytes)
+# Objects smaller than this size will NOT be saved on disk. The
+# value is specified in kilobytes, and the default is 0 KB, which
+# means there is no minimum.
+#Default:
+# minimum_object_size 0 KB
+
+# TAG: maximum_object_size (bytes)
+# Objects larger than this size will NOT be saved on disk. The
+# value is specified in kilobytes, and the default is 4MB. If
+# you wish to get a high BYTES hit ratio, you should probably
+# increase this (one 32 MB object hit counts for 3200 10KB
+# hits). If you wish to increase speed more than your want to
+# save bandwidth you should leave this low.
+#
+# NOTE: if using the LFUDA replacement policy you should increase
+# this value to maximize the byte hit rate improvement of LFUDA!
+# See replacement_policy below for a discussion of this policy.
+#Default:
+# maximum_object_size 4096 KB
+maximum_object_size 153600 KB
+
+# TAG: cache_swap_low (percent, 0-100)
+#Default:
+# cache_swap_low 90
+
+# TAG: cache_swap_high (percent, 0-100)
+#
+# The low- and high-water marks for cache object replacement.
+# Replacement begins when the swap (disk) usage is above the
+# low-water mark and attempts to maintain utilization near the
+# low-water mark. As swap utilization gets close to high-water
+# mark object eviction becomes more aggressive. If utilization is
+# close to the low-water mark less replacement is done each time.
+#
+# Defaults are 90% and 95%. If you have a large cache, 5% could be
+# hundreds of MB. If this is the case you may wish to set these
+# numbers closer together.
+#Default:
+# cache_swap_high 95
+
+# LOGFILE OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: logformat
+# Usage:
+#
+# logformat <name> <format specification>
+#
+# Defines an access log format.
+#
+# The <format specification> is a string with embedded % format codes
+#
+# % format codes all follow the same basic structure where all but
+# the formatcode is optional. Output strings are automatically escaped
+# as required according to their context and the output format
+# modifiers are usually not needed, but can be specified if an explicit
+# output format is desired.
+#
+# % ["|[|'|#] [-] [[0]width] [{argument}] formatcode
+#
+# " output in quoted string format
+# [ output in squid text log format as used by log_mime_hdrs
+# # output in URL quoted format
+# ' output as-is
+#
+# - left aligned
+# width field width. If starting with 0 the
+# output is zero padded
+# {arg} argument such as header name etc
+#
+# Format codes:
+#
+# % a literal % character
+# >a Client source IP address
+# >A Client FQDN
+# >p Client source port
+# <A Server IP address or peer name
+# la Local IP address (http_port)
+# lp Local port number (http_port)
+# <la Local IP address of the last server or peer connection
+# <lp Local port number of the last server or peer connection
+# ts Seconds since epoch
+# tu subsecond time (milliseconds)
+# tl Local time. Optional strftime format argument
+# default %d/%b/%Y:%H:%M:%S %z
+# tg GMT time. Optional strftime format argument
+# default %d/%b/%Y:%H:%M:%S %z
+# tr Response time (milliseconds)
+# dt Total time spent making DNS lookups (milliseconds)
+#
+# HTTP cache related format codes:
+#
+# [http::]>h Original request header. Optional header name argument
+# on the format header[:[separator]element]
+# [http::]>ha The HTTP request headers after adaptation and redirection.
+# Optional header name argument as for >h
+# [http::]<h Reply header. Optional header name argument
+# as for >h
+# [http::]un User name
+# [http::]ul User name from authentication
+# [http::]ui User name from ident
+# [http::]us User name from SSL
+# [http::]ue User name from external acl helper
+# [http::]>Hs HTTP status code sent to the client
+# [http::]<Hs HTTP status code received from the next hop
+# [http::]Ss Squid request status (TCP_MISS etc)
+# [http::]Sh Squid hierarchy status (DEFAULT_PARENT etc)
+# [http::]mt MIME content type
+# [http::]rm Request method (GET/POST etc)
+# [http::]ru Request URL
+# [http::]rp Request URL-Path excluding hostname
+# [http::]rv Request protocol version
+# [http::]et Tag returned by external acl
+# [http::]ea Log string returned by external acl
+# [http::]<st Sent reply size including HTTP headers
+# [http::]>st Received request size including HTTP headers. In the
+# case of chunked requests the chunked encoding metadata
+# are not included
+# [http::]>sh Received HTTP request headers size
+# [http::]<sh Sent HTTP reply headers size
+# [http::]st Request+Reply size including HTTP headers
+# [http::]<sH Reply high offset sent
+# [http::]<sS Upstream object size
+# [http::]<pt Peer response time in milliseconds. The timer starts
+# when the last request byte is sent to the next hop
+# and stops when the last response byte is received.
+# [http::]<tt Total server-side time in milliseconds. The timer
+# starts with the first connect request (or write I/O)
+# sent to the first selected peer. The timer stops
+# with the last I/O with the last peer.
+#
+# If ICAP is enabled, the following two codes become available (as
+# well as ICAP log codes documented with the icap_log option):
+#
+# icap::tt Total ICAP processing time for the HTTP
+# transaction. The timer ticks when ICAP
+# ACLs are checked and when ICAP
+# transaction is in progress.
+#
+# icap::<last_h The header of the last ICAP response
+# related to the HTTP transaction. Like
+# <h, accepts an optional header name
+# argument. Will not change semantics
+# when multiple ICAP transactions per HTTP
+# transaction are supported.
+#
+# If adaptation is enabled the following two codes become available:
+#
+# adapt::sum_trs Summed adaptation transaction response
+# times recorded as a comma-separated list in
+# the order of transaction start time. Each time
+# value is recorded as an integer number,
+# representing response time of one or more
+# adaptation (ICAP or eCAP) transaction in
+# milliseconds. When a failed transaction is
+# being retried or repeated, its time is not
+# logged individually but added to the
+# replacement (next) transaction. See also:
+# adapt::all_trs.
+#
+# adapt::all_trs All adaptation transaction response times.
+# Same as adaptation_strs but response times of
+# individual transactions are never added
+# together. Instead, all transaction response
+# times are recorded individually.
+#
+# You can prefix adapt::*_trs format codes with adaptation
+# service name in curly braces to record response time(s) specific
+# to that service. For example: %{my_service}adapt::sum_trs
+#
+# The default formats available (which do not need re-defining) are:
+#
+#logformat squid %ts.%03tu %6tr %>a %Ss/%03>Hs %<st %rm %ru %un %Sh/%<A %mt
+#logformat squidmime %ts.%03tu %6tr %>a %Ss/%03>Hs %<st %rm %ru %un %Sh/%<A %mt [%>h] [%<h]
+#logformat common %>a %ui %un [%tl] "%rm %ru HTTP/%rv" %>Hs %<st %Ss:%Sh
+#logformat combined %>a %ui %un [%tl] "%rm %ru HTTP/%rv" %>Hs %<st "%{Referer}>h" "%{User-Agent}>h" %Ss:%Sh
+#Default:
+# none
+
+# TAG: access_log
+# These files log client request activities. Has a line every HTTP or
+# ICP request. The format is:
+# access_log <filepath> [<logformat name> [acl acl ...]]
+# access_log none [acl acl ...]]
+#
+# Will log to the specified file using the specified format (which
+# must be defined in a logformat directive) those entries which match
+# ALL the acl's specified (which must be defined in acl clauses).
+#
+# If no acl is specified, all requests will be logged to this file.
+#
+# To disable logging of a request use the filepath "none", in which case
+# a logformat name should not be specified.
+#
+# To log the request via syslog specify a filepath of "syslog":
+#
+# access_log syslog[:facility.priority] [format [acl1 [acl2 ....]]]
+# where facility could be any of:
+# authpriv, daemon, local0 .. local7 or user.
+#
+# And priority could be any of:
+# err, warning, notice, info, debug.
+#
+# Default:
+# access_log /var/log/squid3/access.log squid
+#Default:
+# access_log /var/log/squid3/access.log squid
+
+# TAG: icap_log
+# ICAP log files record ICAP transaction summaries, one line per
+# transaction.
+#
+# The icap_log option format is:
+# icap_log <filepath> [<logformat name> [acl acl ...]]
+# icap_log none [acl acl ...]]
+#
+# Please see access_log option documentation for details. The two
+# kinds of logs share the overall configuration approach and many
+# features.
+#
+# ICAP processing of a single HTTP message or transaction may
+# require multiple ICAP transactions. In such cases, multiple
+# ICAP transaction log lines will correspond to a single access
+# log line.
+#
+# ICAP log uses logformat codes that make sense for an ICAP
+# transaction. Header-related codes are applied to the HTTP header
+# embedded in an ICAP server response, with the following caveats:
+# For REQMOD, there is no HTTP response header unless the ICAP
+# server performed request satisfaction. For RESPMOD, the HTTP
+# request header is the header sent to the ICAP server. For
+# OPTIONS, there are no HTTP headers.
+#
+# The following format codes are also available for ICAP logs:
+#
+# icap::<A ICAP server IP address. Similar to <A.
+#
+# icap::<service_name ICAP service name from the icap_service
+# option in Squid configuration file.
+#
+# icap::ru ICAP Request-URI. Similar to ru.
+#
+# icap::rm ICAP request method (REQMOD, RESPMOD, or
+# OPTIONS). Similar to existing rm.
+#
+# icap::>st Bytes sent to the ICAP server (TCP payload
+# only; i.e., what Squid writes to the socket).
+#
+# icap::<st Bytes received from the ICAP server (TCP
+# payload only; i.e., what Squid reads from
+# the socket).
+#
+# icap::tr Transaction response time (in
+# milliseconds). The timer starts when
+# the ICAP transaction is created and
+# stops when the transaction is completed.
+# Similar to tr.
+#
+# icap::tio Transaction I/O time (in milliseconds). The
+# timer starts when the first ICAP request
+# byte is scheduled for sending. The timers
+# stops when the last byte of the ICAP response
+# is received.
+#
+# icap::to Transaction outcome: ICAP_ERR* for all
+# transaction errors, ICAP_OPT for OPTION
+# transactions, ICAP_ECHO for 204
+# responses, ICAP_MOD for message
+# modification, and ICAP_SAT for request
+# satisfaction. Similar to Ss.
+#
+# icap::Hs ICAP response status code. Similar to Hs.
+#
+# icap::>h ICAP request header(s). Similar to >h.
+#
+# icap::<h ICAP response header(s). Similar to <h.
+#
+# The default ICAP log format, which can be used without an explicit
+# definition, is called icap_squid:
+#
+#logformat icap_squid %ts.%03tu %6icap::tr %>a %icap::to/%03icap::Hs %icap::<size %icap::rm %icap::ru% %un -/%icap::<A -
+#
+# See also: logformat, log_icap, and %icap::<last_h
+#Default:
+# none
+
+# TAG: log_access allow|deny acl acl...
+# This options allows you to control which requests gets logged
+# to access.log (see access_log directive). Requests denied for
+# logging will also not be accounted for in performance counters.
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Default:
+# none
+
+# TAG: log_icap
+# This options allows you to control which requests get logged
+# to icap.log. See the icap_log directive for ICAP log details.
+#Default:
+# none
+
+# TAG: cache_store_log
+# Logs the activities of the storage manager. Shows which
+# objects are ejected from the cache, and which objects are
+# saved and for how long. To disable, enter "none" or remove the line.
+# There are not really utilities to analyze this data, so you can safely
+# disable it.
+#
+# Example:
+# cache_store_log /var/log/squid3/store.log
+#Default:
+# none
+
+# TAG: cache_swap_state
+# Location for the cache "swap.state" file. This index file holds
+# the metadata of objects saved on disk. It is used to rebuild
+# the cache during startup. Normally this file resides in each
+# 'cache_dir' directory, but you may specify an alternate
+# pathname here. Note you must give a full filename, not just
+# a directory. Since this is the index for the whole object
+# list you CANNOT periodically rotate it!
+#
+# If %s can be used in the file name it will be replaced with a
+# a representation of the cache_dir name where each / is replaced
+# with '.'. This is needed to allow adding/removing cache_dir
+# lines when cache_swap_log is being used.
+#
+# If have more than one 'cache_dir', and %s is not used in the name
+# these swap logs will have names such as:
+#
+# cache_swap_log.00
+# cache_swap_log.01
+# cache_swap_log.02
+#
+# The numbered extension (which is added automatically)
+# corresponds to the order of the 'cache_dir' lines in this
+# configuration file. If you change the order of the 'cache_dir'
+# lines in this file, these index files will NOT correspond to
+# the correct 'cache_dir' entry (unless you manually rename
+# them). We recommend you do NOT use this option. It is
+# better to keep these index files in each 'cache_dir' directory.
+#Default:
+# none
+
+# TAG: logfile_rotate
+# Specifies the number of logfile rotations to make when you
+# type 'squid -k rotate'. The default is 10, which will rotate
+# with extensions 0 through 9. Setting logfile_rotate to 0 will
+# disable the file name rotation, but the logfiles are still closed
+# and re-opened. This will enable you to rename the logfiles
+# yourself just before sending the rotate signal.
+#
+# Note, the 'squid -k rotate' command normally sends a USR1
+# signal to the running squid process. In certain situations
+# (e.g. on Linux with Async I/O), USR1 is used for other
+# purposes, so -k rotate uses another signal. It is best to get
+# in the habit of using 'squid -k rotate' instead of 'kill -USR1
+# <pid>'.
+#
+# Note, from Squid-3.1 this option has no effect on the cache.log,
+# that log can be rotated separately by using debug_options
+#
+# Note2, for Debian/Linux the default of logfile_rotate is
+# zero, since it includes external logfile-rotation methods.
+#Default:
+# logfile_rotate 0
+
+# TAG: emulate_httpd_log on|off
+# The Cache can emulate the log file format which many 'httpd'
+# programs use. To disable/enable this emulation, set
+# emulate_httpd_log to 'off' or 'on'. The default
+# is to use the native log format since it includes useful
+# information Squid-specific log analyzers use.
+#Default:
+# emulate_httpd_log off
+
+# TAG: log_ip_on_direct on|off
+# Log the destination IP address in the hierarchy log tag when going
+# direct. Earlier Squid versions logged the hostname here. If you
+# prefer the old way set this to off.
+#Default:
+# log_ip_on_direct on
+
+# TAG: mime_table
+# Pathname to Squid's MIME table. You shouldn't need to change
+# this, but the default file contains examples and formatting
+# information if you do.
+#Default:
+# mime_table /usr/share/squid3/mime.conf
+
+# TAG: log_mime_hdrs on|off
+# The Cache can record both the request and the response MIME
+# headers for each HTTP transaction. The headers are encoded
+# safely and will appear as two bracketed fields at the end of
+# the access log (for either the native or httpd-emulated log
+# formats). To enable this logging set log_mime_hdrs to 'on'.
+#Default:
+# log_mime_hdrs off
+
+# TAG: useragent_log
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-useragent-log option
+#
+# Squid will write the User-Agent field from HTTP requests
+# to the filename specified here. By default useragent_log
+# is disabled.
+#Default:
+# none
+
+# TAG: referer_log
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-referer-log option
+#
+# Squid will write the Referer field from HTTP requests to the
+# filename specified here. By default referer_log is disabled.
+# Note that "referer" is actually a misspelling of "referrer"
+# however the misspelt version has been accepted into the HTTP RFCs
+# and we accept both.
+#Default:
+# none
+
+# TAG: pid_filename
+# A filename to write the process-id to. To disable, enter "none".
+#Default:
+# pid_filename /var/run/squid3.pid
+
+# TAG: log_fqdn on|off
+# Turn this on if you wish to log fully qualified domain names
+# in the access.log. To do this Squid does a DNS lookup of all
+# IP's connecting to it. This can (in some situations) increase
+# latency, which makes your cache seem slower for interactive
+# browsing.
+#Default:
+# log_fqdn off
+
+# TAG: client_netmask
+# A netmask for client addresses in logfiles and cachemgr output.
+# Change this to protect the privacy of your cache clients.
+# A netmask of 255.255.255.0 will log all IP's in that range with
+# the last digit set to '0'.
+#Default:
+# client_netmask no_addr
+
+# TAG: forward_log
+# Note: This option is only available if Squid is rebuilt with the
+# -DWIP_FWD_LOG define
+#
+# Logs the server-side requests.
+#
+# This is currently work in progress.
+#Default:
+# none
+
+# TAG: strip_query_terms
+# By default, Squid strips query terms from requested URLs before
+# logging. This protects your user's privacy.
+#Default:
+# strip_query_terms on
+
+# TAG: buffered_logs on|off
+# cache.log log file is written with stdio functions, and as such
+# it can be buffered or unbuffered. By default it will be unbuffered.
+# Buffering it can speed up the writing slightly (though you are
+# unlikely to need to worry unless you run with tons of debugging
+# enabled in which case performance will suffer badly anyway..).
+#Default:
+# buffered_logs off
+
+# TAG: netdb_filename
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-icmp option
+#
+# A filename where Squid stores it's netdb state between restarts.
+# To disable, enter "none".
+#Default:
+# netdb_filename /var/log/squid3/netdb.state
+
+# OPTIONS FOR TROUBLESHOOTING
+# -----------------------------------------------------------------------------
+
+# TAG: cache_log
+# Cache logging file. This is where general information about
+# your cache's behavior goes. You can increase the amount of data
+# logged to this file and how often its rotated with "debug_options"
+#Default:
+# cache_log /var/log/squid3/cache.log
+
+# TAG: debug_options
+# Logging options are set as section,level where each source file
+# is assigned a unique section. Lower levels result in less
+# output, Full debugging (level 9) can result in a very large
+# log file, so be careful.
+#
+# The magic word "ALL" sets debugging levels for all sections.
+# We recommend normally running with "ALL,1".
+#
+# The rotate=N option can be used to keep more or less of these logs
+# than would otherwise be kept by logfile_rotate.
+# For most uses a single log should be enough to monitor current
+# events affecting Squid.
+#Default:
+# debug_options ALL,1
+
+# TAG: coredump_dir
+# By default Squid leaves core files in the directory from where
+# it was started. If you set 'coredump_dir' to a directory
+# that exists, Squid will chdir() to that directory at startup
+# and coredump files will be left there.
+#
+#Default:
+# coredump_dir none
+#
+
+# Leave coredumps in the first cache dir
+coredump_dir /var/spool/squid3
+
+# OPTIONS FOR FTP GATEWAYING
+# -----------------------------------------------------------------------------
+
+# TAG: ftp_user
+# If you want the anonymous login password to be more informative
+# (and enable the use of picky ftp servers), set this to something
+# reasonable for your domain, like wwwuser@somewhere.net
+#
+# The reason why this is domainless by default is the
+# request can be made on the behalf of a user in any domain,
+# depending on how the cache is used.
+# Some ftp server also validate the email address is valid
+# (for example perl.com).
+#Default:
+# ftp_user Squid@
+
+# TAG: ftp_list_width
+# Sets the width of ftp listings. This should be set to fit in
+# the width of a standard browser. Setting this too small
+# can cut off long filenames when browsing ftp sites.
+#Default:
+# ftp_list_width 32
+
+# TAG: ftp_passive
+# If your firewall does not allow Squid to use passive
+# connections, turn off this option.
+#
+# Use of ftp_epsv_all option requires this to be ON.
+#Default:
+# ftp_passive on
+
+# TAG: ftp_epsv_all
+# FTP Protocol extensions permit the use of a special "EPSV ALL" command.
+#
+# NATs may be able to put the connection on a "fast path" through the
+# translator, as the EPRT command will never be used and therefore,
+# translation of the data portion of the segments will never be needed.
+#
+# When a client only expects to do two-way FTP transfers this may be
+# useful.
+# If squid finds that it must do a three-way FTP transfer after issuing
+# an EPSV ALL command, the FTP session will fail.
+#
+# If you have any doubts about this option do not use it.
+# Squid will nicely attempt all other connection methods.
+#
+# Requires ftp_passive to be ON (default) for any effect.
+#Default:
+# ftp_epsv_all off
+
+# TAG: ftp_epsv
+# FTP Protocol extensions permit the use of a special "EPSV" command.
+#
+# NATs may be able to put the connection on a "fast path" through the
+# translator using EPSV, as the EPRT command will never be used
+# and therefore, translation of the data portion of the segments
+# will never be needed.
+#
+# Turning this OFF will prevent EPSV being attempted.
+# WARNING: Doing so will convert Squid back to the old behavior with all
+# the related problems with external NAT devices/layers.
+#
+# Requires ftp_passive to be ON (default) for any effect.
+#Default:
+# ftp_epsv on
+
+# TAG: ftp_eprt
+# FTP Protocol extensions permit the use of a special "EPRT" command.
+#
+# This extension provides a protocol neutral alternative to the
+# IPv4-only PORT command. When supported it enables active FTP data
+# channels over IPv6 and efficient NAT handling.
+#
+# Turning this OFF will prevent EPRT being attempted and will skip
+# straight to using PORT for IPv4 servers.
+#
+# Some devices are known to not handle this extension correctly and
+# may result in crashes. Devices which suport EPRT enough to fail
+# cleanly will result in Squid attempting PORT anyway. This directive
+# should only be disabled when EPRT results in device failures.
+#
+# WARNING: Doing so will convert Squid back to the old behavior with all
+# the related problems with external NAT devices/layers and IPv4-only FTP.
+#Default:
+# ftp_eprt on
+
+# TAG: ftp_sanitycheck
+# For security and data integrity reasons Squid by default performs
+# sanity checks of the addresses of FTP data connections ensure the
+# data connection is to the requested server. If you need to allow
+# FTP connections to servers using another IP address for the data
+# connection turn this off.
+#Default:
+# ftp_sanitycheck on
+
+# TAG: ftp_telnet_protocol
+# The FTP protocol is officially defined to use the telnet protocol
+# as transport channel for the control connection. However, many
+# implementations are broken and does not respect this aspect of
+# the FTP protocol.
+#
+# If you have trouble accessing files with ASCII code 255 in the
+# path or similar problems involving this ASCII code you can
+# try setting this directive to off. If that helps, report to the
+# operator of the FTP server in question that their FTP server
+# is broken and does not follow the FTP standard.
+#Default:
+# ftp_telnet_protocol on
+
+# OPTIONS FOR EXTERNAL SUPPORT PROGRAMS
+# -----------------------------------------------------------------------------
+
+# TAG: diskd_program
+# Specify the location of the diskd executable.
+# Note this is only useful if you have compiled in
+# diskd as one of the store io modules.
+#Default:
+# diskd_program /usr/lib/squid3/diskd
+
+# TAG: unlinkd_program
+# Specify the location of the executable for file deletion process.
+#Default:
+# unlinkd_program /usr/lib/squid3/unlinkd
+
+# TAG: pinger_program
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-icmp option
+#
+# Specify the location of the executable for the pinger process.
+#Default:
+# pinger_program /usr/lib/squid3/pinger
+
+# TAG: pinger_enable
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-icmp option
+#
+# Control whether the pinger is active at run-time.
+# Enables turning ICMP pinger on and off with a simple
+# squid -k reconfigure.
+#Default:
+# pinger_enable off
+
+# OPTIONS FOR URL REWRITING
+# -----------------------------------------------------------------------------
+
+# TAG: url_rewrite_program
+# Specify the location of the executable URL rewriter to use.
+# Since they can perform almost any function there isn't one included.
+#
+# For each requested URL, the rewriter will receive on line with the format
+#
+# URL <SP> client_ip "/" fqdn <SP> user <SP> method [<SP> kvpairs]<NL>
+#
+# In the future, the rewriter interface will be extended with
+# key=value pairs ("kvpairs" shown above). Rewriter programs
+# should be prepared to receive and possibly ignore additional
+# whitespace-separated tokens on each input line.
+#
+# And the rewriter may return a rewritten URL. The other components of
+# the request line does not need to be returned (ignored if they are).
+#
+# The rewriter can also indicate that a client-side redirect should
+# be performed to the new URL. This is done by prefixing the returned
+# URL with "301:" (moved permanently) or 302: (moved temporarily), etc.
+#
+# By default, a URL rewriter is not used.
+#Default:
+# none
+
+# TAG: url_rewrite_children
+# The number of redirector processes to spawn. If you start
+# too few Squid will have to wait for them to process a backlog of
+# URLs, slowing it down. If you start too many they will use RAM
+# and other system resources.
+#Default:
+# url_rewrite_children 5
+
+# TAG: url_rewrite_concurrency
+# The number of requests each redirector helper can handle in
+# parallel. Defaults to 0 which indicates the redirector
+# is a old-style single threaded redirector.
+#
+# When this directive is set to a value >= 1 then the protocol
+# used to communicate with the helper is modified to include
+# a request ID in front of the request/response. The request
+# ID from the request must be echoed back with the response
+# to that request.
+#Default:
+# url_rewrite_concurrency 0
+
+# TAG: url_rewrite_host_header
+# By default Squid rewrites any Host: header in redirected
+# requests. If you are running an accelerator this may
+# not be a wanted effect of a redirector.
+#
+# WARNING: Entries are cached on the result of the URL rewriting
+# process, so be careful if you have domain-virtual hosts.
+#Default:
+# url_rewrite_host_header on
+
+# TAG: url_rewrite_access
+# If defined, this access list specifies which requests are
+# sent to the redirector processes. By default all requests
+# are sent.
+#
+# This clause supports both fast and slow acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Default:
+# none
+
+# TAG: url_rewrite_bypass
+# When this is 'on', a request will not go through the
+# redirector if all redirectors are busy. If this is 'off'
+# and the redirector queue grows too large, Squid will exit
+# with a FATAL error and ask you to increase the number of
+# redirectors. You should only enable this if the redirectors
+# are not critical to your caching system. If you use
+# redirectors for access control, and you enable this option,
+# users may have access to pages they should not
+# be allowed to request.
+#Default:
+# url_rewrite_bypass off
+
+# OPTIONS FOR TUNING THE CACHE
+# -----------------------------------------------------------------------------
+
+# TAG: cache
+# A list of ACL elements which, if matched and denied, cause the request to
+# not be satisfied from the cache and the reply to not be cached.
+# In other words, use this to force certain objects to never be cached.
+#
+# You must use the words 'allow' or 'deny' to indicate whether items
+# matching the ACL should be allowed or denied into the cache.
+#
+# Default is to allow all to be cached.
+#
+# This clause supports both fast and slow acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Default:
+# none
+
+# TAG: refresh_pattern
+# usage: refresh_pattern [-i] regex min percent max [options]
+#
+# By default, regular expressions are CASE-SENSITIVE. To make
+# them case-insensitive, use the -i option.
+#
+# 'Min' is the time (in minutes) an object without an explicit
+# expiry time should be considered fresh. The recommended
+# value is 0, any higher values may cause dynamic applications
+# to be erroneously cached unless the application designer
+# has taken the appropriate actions.
+#
+# 'Percent' is a percentage of the objects age (time since last
+# modification age) an object without explicit expiry time
+# will be considered fresh.
+#
+# 'Max' is an upper limit on how long objects without an explicit
+# expiry time will be considered fresh.
+#
+# options: override-expire
+# override-lastmod
+# reload-into-ims
+# ignore-reload
+# ignore-no-cache
+# ignore-no-store
+# ignore-must-revalidate
+# ignore-private
+# ignore-auth
+# refresh-ims
+#
+# override-expire enforces min age even if the server
+# sent an explicit expiry time (e.g., with the
+# Expires: header or Cache-Control: max-age). Doing this
+# VIOLATES the HTTP standard. Enabling this feature
+# could make you liable for problems which it causes.
+#
+# Note: override-expire does not enforce staleness - it only extends
+# freshness / min. If the server returns a Expires time which
+# is longer than your max time, Squid will still consider
+# the object fresh for that period of time.
+#
+# override-lastmod enforces min age even on objects
+# that were modified recently.
+#
+# reload-into-ims changes client no-cache or ``reload''
+# to If-Modified-Since requests. Doing this VIOLATES the
+# HTTP standard. Enabling this feature could make you
+# liable for problems which it causes.
+#
+# ignore-reload ignores a client no-cache or ``reload''
+# header. Doing this VIOLATES the HTTP standard. Enabling
+# this feature could make you liable for problems which
+# it causes.
+#
+# ignore-no-cache ignores any ``Pragma: no-cache'' and
+# ``Cache-control: no-cache'' headers received from a server.
+# The HTTP RFC never allows the use of this (Pragma) header
+# from a server, only a client, though plenty of servers
+# send it anyway.
+#
+# ignore-no-store ignores any ``Cache-control: no-store''
+# headers received from a server. Doing this VIOLATES
+# the HTTP standard. Enabling this feature could make you
+# liable for problems which it causes.
+#
+# ignore-must-revalidate ignores any ``Cache-Control: must-revalidate``
+# headers received from a server. Doing this VIOLATES
+# the HTTP standard. Enabling this feature could make you
+# liable for problems which it causes.
+#
+# ignore-private ignores any ``Cache-control: private''
+# headers received from a server. Doing this VIOLATES
+# the HTTP standard. Enabling this feature could make you
+# liable for problems which it causes.
+#
+# ignore-auth caches responses to requests with authorization,
+# as if the originserver had sent ``Cache-control: public''
+# in the response header. Doing this VIOLATES the HTTP standard.
+# Enabling this feature could make you liable for problems which
+# it causes.
+#
+# refresh-ims causes squid to contact the origin server
+# when a client issues an If-Modified-Since request. This
+# ensures that the client will receive an updated version
+# if one is available.
+#
+# Basically a cached object is:
+#
+# FRESH if expires < now, else STALE
+# STALE if age > max
+# FRESH if lm-factor < percent, else STALE
+# FRESH if age < min
+# else STALE
+#
+# The refresh_pattern lines are checked in the order listed here.
+# The first entry which matches is used. If none of the entries
+# match the default will be used.
+#
+# Note, you must uncomment all the default lines if you want
+# to change one. The default setting is only active if none is
+# used.
+#
+#
+
+# Add any of your own refresh_pattern entries above these.
+refresh_pattern ^ftp: 1440 20% 10080
+refresh_pattern ^gopher: 1440 0% 1440
+refresh_pattern -i (/cgi-bin/|\?) 0 0% 0
+refresh_pattern /(|In)Release(|\.gpg)$ 0 0% 0
+refresh_pattern /(Packages|Sources)(|\.gz|\.bz2|\.xz)$ 0 0% 0
+refresh_pattern \.deb$ 129600 100% 129600
+refresh_pattern \.udeb$ 129600 100% 129600
+refresh_pattern \.tar\.(gz|bz2|xz|lzma)$ 129600 100% 129600
+refresh_pattern . 0 20% 4320
+
+# TAG: quick_abort_min (KB)
+#Default:
+# quick_abort_min 16 KB
+
+# TAG: quick_abort_max (KB)
+#Default:
+# quick_abort_max 16 KB
+
+# TAG: quick_abort_pct (percent)
+# The cache by default continues downloading aborted requests
+# which are almost completed (less than 16 KB remaining). This
+# may be undesirable on slow (e.g. SLIP) links and/or very busy
+# caches. Impatient users may tie up file descriptors and
+# bandwidth by repeatedly requesting and immediately aborting
+# downloads.
+#
+# When the user aborts a request, Squid will check the
+# quick_abort values to the amount of data transfered until
+# then.
+#
+# If the transfer has less than 'quick_abort_min' KB remaining,
+# it will finish the retrieval.
+#
+# If the transfer has more than 'quick_abort_max' KB remaining,
+# it will abort the retrieval.
+#
+# If more than 'quick_abort_pct' of the transfer has completed,
+# it will finish the retrieval.
+#
+# If you do not want any retrieval to continue after the client
+# has aborted, set both 'quick_abort_min' and 'quick_abort_max'
+# to '0 KB'.
+#
+# If you want retrievals to always continue if they are being
+# cached set 'quick_abort_min' to '-1 KB'.
+#Default:
+# quick_abort_pct 95
+
+# TAG: read_ahead_gap buffer-size
+# The amount of data the cache will buffer ahead of what has been
+# sent to the client when retrieving an object from another server.
+#Default:
+# read_ahead_gap 16 KB
+
+# TAG: negative_ttl time-units
+# Set the Default Time-to-Live (TTL) for failed requests.
+# Certain types of failures (such as "connection refused" and
+# "404 Not Found") are able to be negatively-cached for a short time.
+# Modern web servers should provide Expires: header, however if they
+# do not this can provide a minimum TTL.
+# The default is not to cache errors with unknown expiry details.
+#
+# Note that this is different from negative caching of DNS lookups.
+#
+# WARNING: Doing this VIOLATES the HTTP standard. Enabling
+# this feature could make you liable for problems which it
+# causes.
+#Default:
+# negative_ttl 0 seconds
+
+# TAG: positive_dns_ttl time-units
+# Upper limit on how long Squid will cache positive DNS responses.
+# Default is 6 hours (360 minutes). This directive must be set
+# larger than negative_dns_ttl.
+#Default:
+# positive_dns_ttl 6 hours
+
+# TAG: negative_dns_ttl time-units
+# Time-to-Live (TTL) for negative caching of failed DNS lookups.
+# This also sets the lower cache limit on positive lookups.
+# Minimum value is 1 second, and it is not recommendable to go
+# much below 10 seconds.
+#Default:
+# negative_dns_ttl 1 minutes
+
+# TAG: range_offset_limit (bytes)
+# Sets a upper limit on how far into the the file a Range request
+# may be to cause Squid to prefetch the whole file. If beyond this
+# limit Squid forwards the Range request as it is and the result
+# is NOT cached.
+#
+# This is to stop a far ahead range request (lets say start at 17MB)
+# from making Squid fetch the whole object up to that point before
+# sending anything to the client.
+#
+# A value of 0 causes Squid to never fetch more than the
+# client requested. (default)
+#
+# A value of -1 causes Squid to always fetch the object from the
+# beginning so it may cache the result. (2.0 style)
+#
+# NP: Using -1 here will override any quick_abort settings that may
+# otherwise apply to the range request. The range request will
+# be fully fetched from start to finish regardless of the client
+# actions. This affects bandwidth usage.
+#Default:
+# range_offset_limit 0 KB
+
+# TAG: minimum_expiry_time (seconds)
+# The minimum caching time according to (Expires - Date)
+# Headers Squid honors if the object can't be revalidated
+# defaults to 60 seconds. In reverse proxy environments it
+# might be desirable to honor shorter object lifetimes. It
+# is most likely better to make your server return a
+# meaningful Last-Modified header however. In ESI environments
+# where page fragments often have short lifetimes, this will
+# often be best set to 0.
+#Default:
+# minimum_expiry_time 60 seconds
+
+# TAG: store_avg_object_size (kbytes)
+# Average object size, used to estimate number of objects your
+# cache can hold. The default is 13 KB.
+#Default:
+# store_avg_object_size 13 KB
+
+# TAG: store_objects_per_bucket
+# Target number of objects per bucket in the store hash table.
+# Lowering this value increases the total number of buckets and
+# also the storage maintenance rate. The default is 20.
+#Default:
+# store_objects_per_bucket 20
+
+# HTTP OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: request_header_max_size (KB)
+# This specifies the maximum size for HTTP headers in a request.
+# Request headers are usually relatively small (about 512 bytes).
+# Placing a limit on the request header size will catch certain
+# bugs (for example with persistent connections) and possibly
+# buffer-overflow or denial-of-service attacks.
+#Default:
+# request_header_max_size 64 KB
+
+# TAG: reply_header_max_size (KB)
+# This specifies the maximum size for HTTP headers in a reply.
+# Reply headers are usually relatively small (about 512 bytes).
+# Placing a limit on the reply header size will catch certain
+# bugs (for example with persistent connections) and possibly
+# buffer-overflow or denial-of-service attacks.
+#Default:
+# reply_header_max_size 64 KB
+
+# TAG: request_body_max_size (bytes)
+# This specifies the maximum size for an HTTP request body.
+# In other words, the maximum size of a PUT/POST request.
+# A user who attempts to send a request with a body larger
+# than this limit receives an "Invalid Request" error message.
+# If you set this parameter to a zero (the default), there will
+# be no limit imposed.
+#Default:
+# request_body_max_size 0 KB
+
+# TAG: client_request_buffer_max_size (bytes)
+# This specifies the maximum buffer size of a client request.
+# It prevents squid eating too much memory when somebody uploads
+# a large file.
+#Default:
+# client_request_buffer_max_size 512 KB
+
+# TAG: chunked_request_body_max_size (bytes)
+# A broken or confused HTTP/1.1 client may send a chunked HTTP
+# request to Squid. Squid does not have full support for that
+# feature yet. To cope with such requests, Squid buffers the
+# entire request and then dechunks request body to create a
+# plain HTTP/1.0 request with a known content length. The plain
+# request is then used by the rest of Squid code as usual.
+#
+# The option value specifies the maximum size of the buffer used
+# to hold the request before the conversion. If the chunked
+# request size exceeds the specified limit, the conversion
+# fails, and the client receives an "unsupported request" error,
+# as if dechunking was disabled.
+#
+# Dechunking is enabled by default. To disable conversion of
+# chunked requests, set the maximum to zero.
+#
+# Request dechunking feature and this option in particular are a
+# temporary hack. When chunking requests and responses are fully
+# supported, there will be no need to buffer a chunked request.
+#Default:
+# chunked_request_body_max_size 64 KB
+
+# TAG: broken_posts
+# A list of ACL elements which, if matched, causes Squid to send
+# an extra CRLF pair after the body of a PUT/POST request.
+#
+# Some HTTP servers has broken implementations of PUT/POST,
+# and rely on an extra CRLF pair sent by some WWW clients.
+#
+# Quote from RFC2616 section 4.1 on this matter:
+#
+# Note: certain buggy HTTP/1.0 client implementations generate an
+# extra CRLF's after a POST request. To restate what is explicitly
+# forbidden by the BNF, an HTTP/1.1 client must not preface or follow
+# a request with an extra CRLF.
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#
+#Example:
+# acl buggy_server url_regex ^http://....
+# broken_posts allow buggy_server
+#Default:
+# none
+
+# TAG: icap_uses_indirect_client on|off
+# Controls whether the indirect client IP address (instead of the direct
+# client IP address) is passed to adaptation services.
+#
+# See also: follow_x_forwarded_for adaptation_send_client_ip
+#Default:
+# icap_uses_indirect_client on
+
+# TAG: via on|off
+# If set (default), Squid will include a Via header in requests and
+# replies as required by RFC2616.
+#Default:
+# via on
+
+# TAG: ie_refresh on|off
+# Microsoft Internet Explorer up until version 5.5 Service
+# Pack 1 has an issue with transparent proxies, wherein it
+# is impossible to force a refresh. Turning this on provides
+# a partial fix to the problem, by causing all IMS-REFRESH
+# requests from older IE versions to check the origin server
+# for fresh content. This reduces hit ratio by some amount
+# (~10% in my experience), but allows users to actually get
+# fresh content when they want it. Note because Squid
+# cannot tell if the user is using 5.5 or 5.5SP1, the behavior
+# of 5.5 is unchanged from old versions of Squid (i.e. a
+# forced refresh is impossible). Newer versions of IE will,
+# hopefully, continue to have the new behavior and will be
+# handled based on that assumption. This option defaults to
+# the old Squid behavior, which is better for hit ratios but
+# worse for clients using IE, if they need to be able to
+# force fresh content.
+#Default:
+# ie_refresh off
+
+# TAG: vary_ignore_expire on|off
+# Many HTTP servers supporting Vary gives such objects
+# immediate expiry time with no cache-control header
+# when requested by a HTTP/1.0 client. This option
+# enables Squid to ignore such expiry times until
+# HTTP/1.1 is fully implemented.
+#
+# WARNING: If turned on this may eventually cause some
+# varying objects not intended for caching to get cached.
+#Default:
+# vary_ignore_expire off
+
+# TAG: request_entities
+# Squid defaults to deny GET and HEAD requests with request entities,
+# as the meaning of such requests are undefined in the HTTP standard
+# even if not explicitly forbidden.
+#
+# Set this directive to on if you have clients which insists
+# on sending request entities in GET or HEAD requests. But be warned
+# that there is server software (both proxies and web servers) which
+# can fail to properly process this kind of request which may make you
+# vulnerable to cache pollution attacks if enabled.
+#Default:
+# request_entities off
+
+# TAG: request_header_access
+# Usage: request_header_access header_name allow|deny [!]aclname ...
+#
+# WARNING: Doing this VIOLATES the HTTP standard. Enabling
+# this feature could make you liable for problems which it
+# causes.
+#
+# This option replaces the old 'anonymize_headers' and the
+# older 'http_anonymizer' option with something that is much
+# more configurable. This new method creates a list of ACLs
+# for each header, allowing you very fine-tuned header
+# mangling.
+#
+# This option only applies to request headers, i.e., from the
+# client to the server.
+#
+# You can only specify known headers for the header name.
+# Other headers are reclassified as 'Other'. You can also
+# refer to all the headers with 'All'.
+#
+# For example, to achieve the same behavior as the old
+# 'http_anonymizer standard' option, you should use:
+#
+# request_header_access From deny all
+# request_header_access Referer deny all
+# request_header_access Server deny all
+# request_header_access User-Agent deny all
+# request_header_access WWW-Authenticate deny all
+# request_header_access Link deny all
+#
+# Or, to reproduce the old 'http_anonymizer paranoid' feature
+# you should use:
+#
+# request_header_access Allow allow all
+# request_header_access Authorization allow all
+# request_header_access WWW-Authenticate allow all
+# request_header_access Proxy-Authorization allow all
+# request_header_access Proxy-Authenticate allow all
+# request_header_access Cache-Control allow all
+# request_header_access Content-Encoding allow all
+# request_header_access Content-Length allow all
+# request_header_access Content-Type allow all
+# request_header_access Date allow all
+# request_header_access Expires allow all
+# request_header_access Host allow all
+# request_header_access If-Modified-Since allow all
+# request_header_access Last-Modified allow all
+# request_header_access Location allow all
+# request_header_access Pragma allow all
+# request_header_access Accept allow all
+# request_header_access Accept-Charset allow all
+# request_header_access Accept-Encoding allow all
+# request_header_access Accept-Language allow all
+# request_header_access Content-Language allow all
+# request_header_access Mime-Version allow all
+# request_header_access Retry-After allow all
+# request_header_access Title allow all
+# request_header_access Connection allow all
+# request_header_access All deny all
+#
+# although many of those are HTTP reply headers, and so should be
+# controlled with the reply_header_access directive.
+#
+# By default, all headers are allowed (no anonymizing is
+# performed).
+#Default:
+# none
+
+# TAG: reply_header_access
+# Usage: reply_header_access header_name allow|deny [!]aclname ...
+#
+# WARNING: Doing this VIOLATES the HTTP standard. Enabling
+# this feature could make you liable for problems which it
+# causes.
+#
+# This option only applies to reply headers, i.e., from the
+# server to the client.
+#
+# This is the same as request_header_access, but in the other
+# direction.
+#
+# This option replaces the old 'anonymize_headers' and the
+# older 'http_anonymizer' option with something that is much
+# more configurable. This new method creates a list of ACLs
+# for each header, allowing you very fine-tuned header
+# mangling.
+#
+# You can only specify known headers for the header name.
+# Other headers are reclassified as 'Other'. You can also
+# refer to all the headers with 'All'.
+#
+# For example, to achieve the same behavior as the old
+# 'http_anonymizer standard' option, you should use:
+#
+# reply_header_access From deny all
+# reply_header_access Referer deny all
+# reply_header_access Server deny all
+# reply_header_access User-Agent deny all
+# reply_header_access WWW-Authenticate deny all
+# reply_header_access Link deny all
+#
+# Or, to reproduce the old 'http_anonymizer paranoid' feature
+# you should use:
+#
+# reply_header_access Allow allow all
+# reply_header_access Authorization allow all
+# reply_header_access WWW-Authenticate allow all
+# reply_header_access Proxy-Authorization allow all
+# reply_header_access Proxy-Authenticate allow all
+# reply_header_access Cache-Control allow all
+# reply_header_access Content-Encoding allow all
+# reply_header_access Content-Length allow all
+# reply_header_access Content-Type allow all
+# reply_header_access Date allow all
+# reply_header_access Expires allow all
+# reply_header_access Host allow all
+# reply_header_access If-Modified-Since allow all
+# reply_header_access Last-Modified allow all
+# reply_header_access Location allow all
+# reply_header_access Pragma allow all
+# reply_header_access Accept allow all
+# reply_header_access Accept-Charset allow all
+# reply_header_access Accept-Encoding allow all
+# reply_header_access Accept-Language allow all
+# reply_header_access Content-Language allow all
+# reply_header_access Mime-Version allow all
+# reply_header_access Retry-After allow all
+# reply_header_access Title allow all
+# reply_header_access Connection allow all
+# reply_header_access All deny all
+#
+# although the HTTP request headers won't be usefully controlled
+# by this directive -- see request_header_access for details.
+#
+# By default, all headers are allowed (no anonymizing is
+# performed).
+#Default:
+# none
+
+# TAG: request_header_replace
+# Usage: request_header_replace header_name message
+# Example: request_header_replace User-Agent Nutscrape/1.0 (CP/M; 8-bit)
+#
+# This option allows you to change the contents of headers
+# denied with request_header_access above, by replacing them
+# with some fixed string. This replaces the old fake_user_agent
+# option.
+#
+# This only applies to request headers, not reply headers.
+#
+# By default, headers are removed if denied.
+#Default:
+# none
+
+# TAG: reply_header_replace
+# Usage: reply_header_replace header_name message
+# Example: reply_header_replace Server Foo/1.0
+#
+# This option allows you to change the contents of headers
+# denied with reply_header_access above, by replacing them
+# with some fixed string.
+#
+# This only applies to reply headers, not request headers.
+#
+# By default, headers are removed if denied.
+#Default:
+# none
+
+# TAG: relaxed_header_parser on|off|warn
+# In the default "on" setting Squid accepts certain forms
+# of non-compliant HTTP messages where it is unambiguous
+# what the sending application intended even if the message
+# is not correctly formatted. The messages is then normalized
+# to the correct form when forwarded by Squid.
+#
+# If set to "warn" then a warning will be emitted in cache.log
+# each time such HTTP error is encountered.
+#
+# If set to "off" then such HTTP errors will cause the request
+# or response to be rejected.
+#Default:
+# relaxed_header_parser on
+
+# TAG: ignore_expect_100 on|off
+# This option makes Squid ignore any Expect: 100-continue header present
+# in the request. RFC 2616 requires that Squid being unable to satisfy
+# the response expectation MUST return a 417 error.
+#
+# Note: Enabling this is a HTTP protocol violation, but some clients may
+# not handle it well..
+#Default:
+# ignore_expect_100 off
+
+# TIMEOUTS
+# -----------------------------------------------------------------------------
+
+# TAG: forward_timeout time-units
+# This parameter specifies how long Squid should at most attempt in
+# finding a forwarding path for the request before giving up.
+#Default:
+# forward_timeout 4 minutes
+
+# TAG: connect_timeout time-units
+# This parameter specifies how long to wait for the TCP connect to
+# the requested server or peer to complete before Squid should
+# attempt to find another path where to forward the request.
+#Default:
+# connect_timeout 1 minute
+
+# TAG: peer_connect_timeout time-units
+# This parameter specifies how long to wait for a pending TCP
+# connection to a peer cache. The default is 30 seconds. You
+# may also set different timeout values for individual neighbors
+# with the 'connect-timeout' option on a 'cache_peer' line.
+#Default:
+# peer_connect_timeout 30 seconds
+
+# TAG: read_timeout time-units
+# The read_timeout is applied on server-side connections. After
+# each successful read(), the timeout will be extended by this
+# amount. If no data is read again after this amount of time,
+# the request is aborted and logged with ERR_READ_TIMEOUT. The
+# default is 15 minutes.
+#Default:
+# read_timeout 15 minutes
+
+# TAG: request_timeout
+# How long to wait for complete HTTP request headers after initial
+# connection establishment.
+#Default:
+# request_timeout 5 minutes
+
+# TAG: persistent_request_timeout
+# How long to wait for the next HTTP request on a persistent
+# connection after the previous request completes.
+#Default:
+# persistent_request_timeout 2 minutes
+
+# TAG: client_lifetime time-units
+# The maximum amount of time a client (browser) is allowed to
+# remain connected to the cache process. This protects the Cache
+# from having a lot of sockets (and hence file descriptors) tied up
+# in a CLOSE_WAIT state from remote clients that go away without
+# properly shutting down (either because of a network failure or
+# because of a poor client implementation). The default is one
+# day, 1440 minutes.
+#
+# NOTE: The default value is intended to be much larger than any
+# client would ever need to be connected to your cache. You
+# should probably change client_lifetime only as a last resort.
+# If you seem to have many client connections tying up
+# filedescriptors, we recommend first tuning the read_timeout,
+# request_timeout, persistent_request_timeout and quick_abort values.
+#Default:
+# client_lifetime 1 day
+
+# TAG: half_closed_clients
+# Some clients may shutdown the sending side of their TCP
+# connections, while leaving their receiving sides open. Sometimes,
+# Squid can not tell the difference between a half-closed and a
+# fully-closed TCP connection.
+#
+# By default, Squid will immediately close client connections when
+# read(2) returns "no more data to read."
+#
+# Change this option to 'on' and Squid will keep open connections
+# until a read(2) or write(2) on the socket returns an error.
+# This may show some benefits for reverse proxies. But if not
+# it is recommended to leave OFF.
+#Default:
+# half_closed_clients off
+
+# TAG: pconn_timeout
+# Timeout for idle persistent connections to servers and other
+# proxies.
+#Default:
+# pconn_timeout 1 minute
+
+# TAG: ident_timeout
+# Maximum time to wait for IDENT lookups to complete.
+#
+# If this is too high, and you enabled IDENT lookups from untrusted
+# users, you might be susceptible to denial-of-service by having
+# many ident requests going at once.
+#Default:
+# ident_timeout 10 seconds
+
+# TAG: shutdown_lifetime time-units
+# When SIGTERM or SIGHUP is received, the cache is put into
+# "shutdown pending" mode until all active sockets are closed.
+# This value is the lifetime to set for all open descriptors
+# during shutdown mode. Any active clients after this many
+# seconds will receive a 'timeout' message.
+#Default:
+# shutdown_lifetime 30 seconds
+
+# ADMINISTRATIVE PARAMETERS
+# -----------------------------------------------------------------------------
+
+# TAG: cache_mgr
+# Email-address of local cache manager who will receive
+# mail if the cache dies. The default is "webmaster."
+#Default:
+# cache_mgr webmaster
+
+# TAG: mail_from
+# From: email-address for mail sent when the cache dies.
+# The default is to use 'appname@unique_hostname'.
+# Default appname value is "squid", can be changed into
+# src/globals.h before building squid.
+#Default:
+# none
+
+# TAG: mail_program
+# Email program used to send mail if the cache dies.
+# The default is "mail". The specified program must comply
+# with the standard Unix mail syntax:
+# mail-program recipient < mailfile
+#
+# Optional command line options can be specified.
+#Default:
+# mail_program mail
+
+# TAG: cache_effective_user
+# If you start Squid as root, it will change its effective/real
+# UID/GID to the user specified below. The default is to change
+# to UID of proxy.
+# see also; cache_effective_group
+#Default:
+# cache_effective_user proxy
+
+# TAG: cache_effective_group
+# Squid sets the GID to the effective user's default group ID
+# (taken from the password file) and supplementary group list
+# from the groups membership.
+#
+# If you want Squid to run with a specific GID regardless of
+# the group memberships of the effective user then set this
+# to the group (or GID) you want Squid to run as. When set
+# all other group privileges of the effective user are ignored
+# and only this GID is effective. If Squid is not started as
+# root the user starting Squid MUST be member of the specified
+# group.
+#
+# This option is not recommended by the Squid Team.
+# Our preference is for administrators to configure a secure
+# user account for squid with UID/GID matching system policies.
+#Default:
+# none
+
+# TAG: httpd_suppress_version_string on|off
+# Suppress Squid version string info in HTTP headers and HTML error pages.
+#Default:
+# httpd_suppress_version_string off
+
+# TAG: visible_hostname
+# If you want to present a special hostname in error messages, etc,
+# define this. Otherwise, the return value of gethostname()
+# will be used. If you have multiple caches in a cluster and
+# get errors about IP-forwarding you must set them to have individual
+# names with this setting.
+#Default:
+# visible_hostname localhost
+
+# TAG: unique_hostname
+# If you want to have multiple machines with the same
+# 'visible_hostname' you must give each machine a different
+# 'unique_hostname' so forwarding loops can be detected.
+#Default:
+# none
+
+# TAG: hostname_aliases
+# A list of other DNS names your cache has.
+#Default:
+# none
+
+# TAG: umask
+# Minimum umask which should be enforced while the proxy
+# is running, in addition to the umask set at startup.
+#
+# For a traditional octal representation of umasks, start
+# your value with 0.
+#Default:
+# umask 027
+
+# OPTIONS FOR THE CACHE REGISTRATION SERVICE
+# -----------------------------------------------------------------------------
+#
+# This section contains parameters for the (optional) cache
+# announcement service. This service is provided to help
+# cache administrators locate one another in order to join or
+# create cache hierarchies.
+#
+# An 'announcement' message is sent (via UDP) to the registration
+# service by Squid. By default, the announcement message is NOT
+# SENT unless you enable it with 'announce_period' below.
+#
+# The announcement message includes your hostname, plus the
+# following information from this configuration file:
+#
+# http_port
+# icp_port
+# cache_mgr
+#
+# All current information is processed regularly and made
+# available on the Web at http://www.ircache.net/Cache/Tracker/.
+
+# TAG: announce_period
+# This is how frequently to send cache announcements. The
+# default is `0' which disables sending the announcement
+# messages.
+#
+# To enable announcing your cache, just set an announce period.
+#
+# Example:
+# announce_period 1 day
+#Default:
+# announce_period 0
+
+# TAG: announce_host
+#Default:
+# announce_host tracker.ircache.net
+
+# TAG: announce_file
+#Default:
+# none
+
+# TAG: announce_port
+# announce_host and announce_port set the hostname and port
+# number where the registration message will be sent.
+#
+# Hostname will default to 'tracker.ircache.net' and port will
+# default default to 3131. If the 'filename' argument is given,
+# the contents of that file will be included in the announce
+# message.
+#Default:
+# announce_port 3131
+
+# HTTPD-ACCELERATOR OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: httpd_accel_surrogate_id
+# Surrogates (http://www.esi.org/architecture_spec_1.0.html)
+# need an identification token to allow control targeting. Because
+# a farm of surrogates may all perform the same tasks, they may share
+# an identification token.
+#Default:
+# httpd_accel_surrogate_id unset-id
+
+# TAG: http_accel_surrogate_remote on|off
+# Remote surrogates (such as those in a CDN) honour Surrogate-Control: no-store-remote.
+# Set this to on to have squid behave as a remote surrogate.
+#Default:
+# http_accel_surrogate_remote off
+
+# TAG: esi_parser libxml2|expat|custom
+# ESI markup is not strictly XML compatible. The custom ESI parser
+# will give higher performance, but cannot handle non ASCII character
+# encodings.
+#Default:
+# esi_parser custom
+
+# DELAY POOL PARAMETERS
+# -----------------------------------------------------------------------------
+
+# TAG: delay_pools
+# This represents the number of delay pools to be used. For example,
+# if you have one class 2 delay pool and one class 3 delays pool, you
+# have a total of 2 delay pools.
+#Default:
+# delay_pools 0
+
+# TAG: delay_class
+# This defines the class of each delay pool. There must be exactly one
+# delay_class line for each delay pool. For example, to define two
+# delay pools, one of class 2 and one of class 3, the settings above
+# and here would be:
+#
+# Example:
+# delay_pools 4 # 4 delay pools
+# delay_class 1 2 # pool 1 is a class 2 pool
+# delay_class 2 3 # pool 2 is a class 3 pool
+# delay_class 3 4 # pool 3 is a class 4 pool
+# delay_class 4 5 # pool 4 is a class 5 pool
+#
+# The delay pool classes are:
+#
+# class 1 Everything is limited by a single aggregate
+# bucket.
+#
+# class 2 Everything is limited by a single aggregate
+# bucket as well as an "individual" bucket chosen
+# from bits 25 through 32 of the IPv4 address.
+#
+# class 3 Everything is limited by a single aggregate
+# bucket as well as a "network" bucket chosen
+# from bits 17 through 24 of the IP address and a
+# "individual" bucket chosen from bits 17 through
+# 32 of the IPv4 address.
+#
+# class 4 Everything in a class 3 delay pool, with an
+# additional limit on a per user basis. This
+# only takes effect if the username is established
+# in advance - by forcing authentication in your
+# http_access rules.
+#
+# class 5 Requests are grouped according their tag (see
+# external_acl's tag= reply).
+#
+#
+# Each pool also requires a delay_parameters directive to configure the pool size
+# and speed limits used whenever the pool is applied to a request. Along with
+# a set of delay_access directives to determine when it is used.
+#
+# NOTE: If an IP address is a.b.c.d
+# -> bits 25 through 32 are "d"
+# -> bits 17 through 24 are "c"
+# -> bits 17 through 32 are "c * 256 + d"
+#
+# NOTE-2: Due to the use of bitmasks in class 2,3,4 pools they only apply to
+# IPv4 traffic. Class 1 and 5 pools may be used with IPv6 traffic.
+#Default:
+# none
+
+# TAG: delay_access
+# This is used to determine which delay pool a request falls into.
+#
+# delay_access is sorted per pool and the matching starts with pool 1,
+# then pool 2, ..., and finally pool N. The first delay pool where the
+# request is allowed is selected for the request. If it does not allow
+# the request to any pool then the request is not delayed (default).
+#
+# For example, if you want some_big_clients in delay
+# pool 1 and lotsa_little_clients in delay pool 2:
+#
+#Example:
+# delay_access 1 allow some_big_clients
+# delay_access 1 deny all
+# delay_access 2 allow lotsa_little_clients
+# delay_access 2 deny all
+# delay_access 3 allow authenticated_clients
+#Default:
+# none
+
+# TAG: delay_parameters
+# This defines the parameters for a delay pool. Each delay pool has
+# a number of "buckets" associated with it, as explained in the
+# description of delay_class.
+#
+# For a class 1 delay pool, the syntax is:
+# delay_pools pool 1
+# delay_parameters pool aggregate
+#
+# For a class 2 delay pool:
+# delay_pools pool 2
+# delay_parameters pool aggregate individual
+#
+# For a class 3 delay pool:
+# delay_pools pool 3
+# delay_parameters pool aggregate network individual
+#
+# For a class 4 delay pool:
+# delay_pools pool 4
+# delay_parameters pool aggregate network individual user
+#
+# For a class 5 delay pool:
+# delay_pools pool 5
+# delay_parameters pool tagrate
+#
+# The option variables are:
+#
+# pool a pool number - ie, a number between 1 and the
+# number specified in delay_pools as used in
+# delay_class lines.
+#
+# aggregate the speed limit parameters for the aggregate bucket
+# (class 1, 2, 3).
+#
+# individual the speed limit parameters for the individual
+# buckets (class 2, 3).
+#
+# network the speed limit parameters for the network buckets
+# (class 3).
+#
+# user the speed limit parameters for the user buckets
+# (class 4).
+#
+# tagrate the speed limit parameters for the tag buckets
+# (class 5).
+#
+# A pair of delay parameters is written restore/maximum, where restore is
+# the number of bytes (not bits - modem and network speeds are usually
+# quoted in bits) per second placed into the bucket, and maximum is the
+# maximum number of bytes which can be in the bucket at any time.
+#
+# There must be one delay_parameters line for each delay pool.
+#
+#
+# For example, if delay pool number 1 is a class 2 delay pool as in the
+# above example, and is being used to strictly limit each host to 64Kbit/sec
+# (plus overheads), with no overall limit, the line is:
+#
+# delay_parameters 1 -1/-1 8000/8000
+#
+# Note that 8 x 8000 KByte/sec -> 64Kbit/sec.
+#
+# Note that the figure -1 is used to represent "unlimited".
+#
+#
+# And, if delay pool number 2 is a class 3 delay pool as in the above
+# example, and you want to limit it to a total of 256Kbit/sec (strict limit)
+# with each 8-bit network permitted 64Kbit/sec (strict limit) and each
+# individual host permitted 4800bit/sec with a bucket maximum size of 64Kbits
+# to permit a decent web page to be downloaded at a decent speed
+# (if the network is not being limited due to overuse) but slow down
+# large downloads more significantly:
+#
+# delay_parameters 2 32000/32000 8000/8000 600/8000
+#
+# Note that 8 x 32000 KByte/sec -> 256Kbit/sec.
+# 8 x 8000 KByte/sec -> 64Kbit/sec.
+# 8 x 600 Byte/sec -> 4800bit/sec.
+#
+#
+# Finally, for a class 4 delay pool as in the example - each user will
+# be limited to 128Kbits/sec no matter how many workstations they are logged into.:
+#
+# delay_parameters 4 32000/32000 8000/8000 600/64000 16000/16000
+#Default:
+# none
+
+# TAG: delay_initial_bucket_level (percent, 0-100)
+# The initial bucket percentage is used to determine how much is put
+# in each bucket when squid starts, is reconfigured, or first notices
+# a host accessing it (in class 2 and class 3, individual hosts and
+# networks only have buckets associated with them once they have been
+# "seen" by squid).
+#Default:
+# delay_initial_bucket_level 50
+
+# WCCPv1 AND WCCPv2 CONFIGURATION OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: wccp_router
+# Use this option to define your WCCP ``home'' router for
+# Squid.
+#
+# wccp_router supports a single WCCP(v1) router
+#
+# wccp2_router supports multiple WCCPv2 routers
+#
+# only one of the two may be used at the same time and defines
+# which version of WCCP to use.
+#Default:
+# wccp_router any_addr
+
+# TAG: wccp2_router
+# Use this option to define your WCCP ``home'' router for
+# Squid.
+#
+# wccp_router supports a single WCCP(v1) router
+#
+# wccp2_router supports multiple WCCPv2 routers
+#
+# only one of the two may be used at the same time and defines
+# which version of WCCP to use.
+#Default:
+# none
+
+# TAG: wccp_version
+# This directive is only relevant if you need to set up WCCP(v1)
+# to some very old and end-of-life Cisco routers. In all other
+# setups it must be left unset or at the default setting.
+# It defines an internal version in the WCCP(v1) protocol,
+# with version 4 being the officially documented protocol.
+#
+# According to some users, Cisco IOS 11.2 and earlier only
+# support WCCP version 3. If you're using that or an earlier
+# version of IOS, you may need to change this value to 3, otherwise
+# do not specify this parameter.
+#Default:
+# wccp_version 4
+
+# TAG: wccp2_rebuild_wait
+# If this is enabled Squid will wait for the cache dir rebuild to finish
+# before sending the first wccp2 HereIAm packet
+#Default:
+# wccp2_rebuild_wait on
+
+# TAG: wccp2_forwarding_method
+# WCCP2 allows the setting of forwarding methods between the
+# router/switch and the cache. Valid values are as follows:
+#
+# gre - GRE encapsulation (forward the packet in a GRE/WCCP tunnel)
+# l2 - L2 redirect (forward the packet using Layer 2/MAC rewriting)
+#
+# Currently (as of IOS 12.4) cisco routers only support GRE.
+# Cisco switches only support the L2 redirect assignment method.
+#Default:
+# wccp2_forwarding_method gre
+
+# TAG: wccp2_return_method
+# WCCP2 allows the setting of return methods between the
+# router/switch and the cache for packets that the cache
+# decides not to handle. Valid values are as follows:
+#
+# gre - GRE encapsulation (forward the packet in a GRE/WCCP tunnel)
+# l2 - L2 redirect (forward the packet using Layer 2/MAC rewriting)
+#
+# Currently (as of IOS 12.4) cisco routers only support GRE.
+# Cisco switches only support the L2 redirect assignment.
+#
+# If the "ip wccp redirect exclude in" command has been
+# enabled on the cache interface, then it is still safe for
+# the proxy server to use a l2 redirect method even if this
+# option is set to GRE.
+#Default:
+# wccp2_return_method gre
+
+# TAG: wccp2_assignment_method
+# WCCP2 allows the setting of methods to assign the WCCP hash
+# Valid values are as follows:
+#
+# hash - Hash assignment
+# mask - Mask assignment
+#
+# As a general rule, cisco routers support the hash assignment method
+# and cisco switches support the mask assignment method.
+#Default:
+# wccp2_assignment_method hash
+
+# TAG: wccp2_service
+# WCCP2 allows for multiple traffic services. There are two
+# types: "standard" and "dynamic". The standard type defines
+# one service id - http (id 0). The dynamic service ids can be from
+# 51 to 255 inclusive. In order to use a dynamic service id
+# one must define the type of traffic to be redirected; this is done
+# using the wccp2_service_info option.
+#
+# The "standard" type does not require a wccp2_service_info option,
+# just specifying the service id will suffice.
+#
+# MD5 service authentication can be enabled by adding
+# "password=<password>" to the end of this service declaration.
+#
+# Examples:
+#
+# wccp2_service standard 0 # for the 'web-cache' standard service
+# wccp2_service dynamic 80 # a dynamic service type which will be
+# # fleshed out with subsequent options.
+# wccp2_service standard 0 password=foo
+#Default:
+# wccp2_service standard 0
+
+# TAG: wccp2_service_info
+# Dynamic WCCPv2 services require further information to define the
+# traffic you wish to have diverted.
+#
+# The format is:
+#
+# wccp2_service_info <id> protocol=<protocol> flags=<flag>,<flag>..
+# priority=<priority> ports=<port>,<port>..
+#
+# The relevant WCCPv2 flags:
+# + src_ip_hash, dst_ip_hash
+# + source_port_hash, dst_port_hash
+# + src_ip_alt_hash, dst_ip_alt_hash
+# + src_port_alt_hash, dst_port_alt_hash
+# + ports_source
+#
+# The port list can be one to eight entries.
+#
+# Example:
+#
+# wccp2_service_info 80 protocol=tcp flags=src_ip_hash,ports_source
+# priority=240 ports=80
+#
+# Note: the service id must have been defined by a previous
+# 'wccp2_service dynamic <id>' entry.
+#Default:
+# none
+
+# TAG: wccp2_weight
+# Each cache server gets assigned a set of the destination
+# hash proportional to their weight.
+#Default:
+# wccp2_weight 10000
+
+# TAG: wccp_address
+#Default:
+# wccp_address 0.0.0.0
+
+# TAG: wccp2_address
+# Use this option if you require WCCP to use a specific
+# interface address.
+#
+# The default behavior is to not bind to any specific address.
+#Default:
+# wccp2_address 0.0.0.0
+
+# PERSISTENT CONNECTION HANDLING
+# -----------------------------------------------------------------------------
+#
+# Also see "pconn_timeout" in the TIMEOUTS section
+
+# TAG: client_persistent_connections
+#Default:
+# client_persistent_connections on
+
+# TAG: server_persistent_connections
+# Persistent connection support for clients and servers. By
+# default, Squid uses persistent connections (when allowed)
+# with its clients and servers. You can use these options to
+# disable persistent connections with clients and/or servers.
+#Default:
+# server_persistent_connections on
+
+# TAG: persistent_connection_after_error
+# With this directive the use of persistent connections after
+# HTTP errors can be disabled. Useful if you have clients
+# who fail to handle errors on persistent connections proper.
+#Default:
+# persistent_connection_after_error on
+
+# TAG: detect_broken_pconn
+# Some servers have been found to incorrectly signal the use
+# of HTTP/1.0 persistent connections even on replies not
+# compatible, causing significant delays. This server problem
+# has mostly been seen on redirects.
+#
+# By enabling this directive Squid attempts to detect such
+# broken replies and automatically assume the reply is finished
+# after 10 seconds timeout.
+#Default:
+# detect_broken_pconn off
+
+# CACHE DIGEST OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: digest_generation
+# This controls whether the server will generate a Cache Digest
+# of its contents. By default, Cache Digest generation is
+# enabled if Squid is compiled with --enable-cache-digests defined.
+#Default:
+# digest_generation on
+
+# TAG: digest_bits_per_entry
+# This is the number of bits of the server's Cache Digest which
+# will be associated with the Digest entry for a given HTTP
+# Method and URL (public key) combination. The default is 5.
+#Default:
+# digest_bits_per_entry 5
+
+# TAG: digest_rebuild_period (seconds)
+# This is the wait time between Cache Digest rebuilds.
+#Default:
+# digest_rebuild_period 1 hour
+
+# TAG: digest_rewrite_period (seconds)
+# This is the wait time between Cache Digest writes to
+# disk.
+#Default:
+# digest_rewrite_period 1 hour
+
+# TAG: digest_swapout_chunk_size (bytes)
+# This is the number of bytes of the Cache Digest to write to
+# disk at a time. It defaults to 4096 bytes (4KB), the Squid
+# default swap page.
+#Default:
+# digest_swapout_chunk_size 4096 bytes
+
+# TAG: digest_rebuild_chunk_percentage (percent, 0-100)
+# This is the percentage of the Cache Digest to be scanned at a
+# time. By default it is set to 10% of the Cache Digest.
+#Default:
+# digest_rebuild_chunk_percentage 10
+
+# SNMP OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: snmp_port
+# The port number where Squid listens for SNMP requests. To enable
+# SNMP support set this to a suitable port number. Port number
+# 3401 is often used for the Squid SNMP agent. By default it's
+# set to "0" (disabled)
+#
+# Example:
+# snmp_port 3401
+#Default:
+# snmp_port 0
+
+# TAG: snmp_access
+# Allowing or denying access to the SNMP port.
+#
+# All access to the agent is denied by default.
+# usage:
+#
+# snmp_access allow|deny [!]aclname ...
+#
+# This clause only supports fast acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Example:
+# snmp_access allow snmppublic localhost
+# snmp_access deny all
+#Default:
+# snmp_access deny all
+
+# TAG: snmp_incoming_address
+#Default:
+# snmp_incoming_address any_addr
+
+# TAG: snmp_outgoing_address
+# Just like 'udp_incoming_address', but for the SNMP port.
+#
+# snmp_incoming_address is used for the SNMP socket receiving
+# messages from SNMP agents.
+# snmp_outgoing_address is used for SNMP packets returned to SNMP
+# agents.
+#
+# The default snmp_incoming_address is to listen on all
+# available network interfaces.
+#
+# If snmp_outgoing_address is not set it will use the same socket
+# as snmp_incoming_address. Only change this if you want to have
+# SNMP replies sent using another address than where this Squid
+# listens for SNMP queries.
+#
+# NOTE, snmp_incoming_address and snmp_outgoing_address can not have
+# the same value since they both use port 3401.
+#Default:
+# snmp_outgoing_address no_addr
+
+# ICP OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: icp_port
+# The port number where Squid sends and receives ICP queries to
+# and from neighbor caches. The standard UDP port for ICP is 3130.
+# Default is disabled (0).
+#
+# Example:
+# icp_port 3130
+#Default:
+# icp_port 0
+
+# TAG: htcp_port
+# The port number where Squid sends and receives HTCP queries to
+# and from neighbor caches. To turn it on you want to set it to
+# 4827. By default it is set to "0" (disabled).
+#
+# Example:
+# htcp_port 4827
+#Default:
+# htcp_port 0
+
+# TAG: log_icp_queries on|off
+# If set, ICP queries are logged to access.log. You may wish
+# do disable this if your ICP load is VERY high to speed things
+# up or to simplify log analysis.
+#Default:
+# log_icp_queries on
+
+# TAG: udp_incoming_address
+# udp_incoming_address is used for UDP packets received from other
+# caches.
+#
+# The default behavior is to not bind to any specific address.
+#
+# Only change this if you want to have all UDP queries received on
+# a specific interface/address.
+#
+# NOTE: udp_incoming_address is used by the ICP, HTCP, and DNS
+# modules. Altering it will affect all of them in the same manner.
+#
+# see also; udp_outgoing_address
+#
+# NOTE, udp_incoming_address and udp_outgoing_address can not
+# have the same value since they both use the same port.
+#Default:
+# udp_incoming_address any_addr
+
+# TAG: udp_outgoing_address
+# udp_outgoing_address is used for UDP packets sent out to other
+# caches.
+#
+# The default behavior is to not bind to any specific address.
+#
+# Instead it will use the same socket as udp_incoming_address.
+# Only change this if you want to have UDP queries sent using another
+# address than where this Squid listens for UDP queries from other
+# caches.
+#
+# NOTE: udp_outgoing_address is used by the ICP, HTCP, and DNS
+# modules. Altering it will affect all of them in the same manner.
+#
+# see also; udp_incoming_address
+#
+# NOTE, udp_incoming_address and udp_outgoing_address can not
+# have the same value since they both use the same port.
+#Default:
+# udp_outgoing_address no_addr
+
+# TAG: icp_hit_stale on|off
+# If you want to return ICP_HIT for stale cache objects, set this
+# option to 'on'. If you have sibling relationships with caches
+# in other administrative domains, this should be 'off'. If you only
+# have sibling relationships with caches under your control,
+# it is probably okay to set this to 'on'.
+# If set to 'on', your siblings should use the option "allow-miss"
+# on their cache_peer lines for connecting to you.
+#Default:
+# icp_hit_stale off
+
+# TAG: minimum_direct_hops
+# If using the ICMP pinging stuff, do direct fetches for sites
+# which are no more than this many hops away.
+#Default:
+# minimum_direct_hops 4
+
+# TAG: minimum_direct_rtt
+# If using the ICMP pinging stuff, do direct fetches for sites
+# which are no more than this many rtt milliseconds away.
+#Default:
+# minimum_direct_rtt 400
+
+# TAG: netdb_low
+#Default:
+# netdb_low 900
+
+# TAG: netdb_high
+# The low and high water marks for the ICMP measurement
+# database. These are counts, not percents. The defaults are
+# 900 and 1000. When the high water mark is reached, database
+# entries will be deleted until the low mark is reached.
+#Default:
+# netdb_high 1000
+
+# TAG: netdb_ping_period
+# The minimum period for measuring a site. There will be at
+# least this much delay between successive pings to the same
+# network. The default is five minutes.
+#Default:
+# netdb_ping_period 5 minutes
+
+# TAG: query_icmp on|off
+# If you want to ask your peers to include ICMP data in their ICP
+# replies, enable this option.
+#
+# If your peer has configured Squid (during compilation) with
+# '--enable-icmp' that peer will send ICMP pings to origin server
+# sites of the URLs it receives. If you enable this option the
+# ICP replies from that peer will include the ICMP data (if available).
+# Then, when choosing a parent cache, Squid will choose the parent with
+# the minimal RTT to the origin server. When this happens, the
+# hierarchy field of the access.log will be
+# "CLOSEST_PARENT_MISS". This option is off by default.
+#Default:
+# query_icmp off
+
+# TAG: test_reachability on|off
+# When this is 'on', ICP MISS replies will be ICP_MISS_NOFETCH
+# instead of ICP_MISS if the target host is NOT in the ICMP
+# database, or has a zero RTT.
+#Default:
+# test_reachability off
+
+# TAG: icp_query_timeout (msec)
+# Normally Squid will automatically determine an optimal ICP
+# query timeout value based on the round-trip-time of recent ICP
+# queries. If you want to override the value determined by
+# Squid, set this 'icp_query_timeout' to a non-zero value. This
+# value is specified in MILLISECONDS, so, to use a 2-second
+# timeout (the old default), you would write:
+#
+# icp_query_timeout 2000
+#Default:
+# icp_query_timeout 0
+
+# TAG: maximum_icp_query_timeout (msec)
+# Normally the ICP query timeout is determined dynamically. But
+# sometimes it can lead to very large values (say 5 seconds).
+# Use this option to put an upper limit on the dynamic timeout
+# value. Do NOT use this option to always use a fixed (instead
+# of a dynamic) timeout value. To set a fixed timeout see the
+# 'icp_query_timeout' directive.
+#Default:
+# maximum_icp_query_timeout 2000
+
+# TAG: minimum_icp_query_timeout (msec)
+# Normally the ICP query timeout is determined dynamically. But
+# sometimes it can lead to very small timeouts, even lower than
+# the normal latency variance on your link due to traffic.
+# Use this option to put an lower limit on the dynamic timeout
+# value. Do NOT use this option to always use a fixed (instead
+# of a dynamic) timeout value. To set a fixed timeout see the
+# 'icp_query_timeout' directive.
+#Default:
+# minimum_icp_query_timeout 5
+
+# TAG: background_ping_rate time-units
+# Controls how often the ICP pings are sent to siblings that
+# have background-ping set.
+#Default:
+# background_ping_rate 10 seconds
+
+# MULTICAST ICP OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: mcast_groups
+# This tag specifies a list of multicast groups which your server
+# should join to receive multicasted ICP queries.
+#
+# NOTE! Be very careful what you put here! Be sure you
+# understand the difference between an ICP _query_ and an ICP
+# _reply_. This option is to be set only if you want to RECEIVE
+# multicast queries. Do NOT set this option to SEND multicast
+# ICP (use cache_peer for that). ICP replies are always sent via
+# unicast, so this option does not affect whether or not you will
+# receive replies from multicast group members.
+#
+# You must be very careful to NOT use a multicast address which
+# is already in use by another group of caches.
+#
+# If you are unsure about multicast, please read the Multicast
+# chapter in the Squid FAQ (http://www.squid-cache.org/FAQ/).
+#
+# Usage: mcast_groups 239.128.16.128 224.0.1.20
+#
+# By default, Squid doesn't listen on any multicast groups.
+#Default:
+# none
+
+# TAG: mcast_miss_addr
+# Note: This option is only available if Squid is rebuilt with the
+# -DMULTICAST_MISS_STREAM define
+#
+# If you enable this option, every "cache miss" URL will
+# be sent out on the specified multicast address.
+#
+# Do not enable this option unless you are are absolutely
+# certain you understand what you are doing.
+#Default:
+# mcast_miss_addr no_addr
+
+# TAG: mcast_miss_ttl
+# Note: This option is only available if Squid is rebuilt with the
+# -DMULTICAST_MISS_STREAM define
+#
+# This is the time-to-live value for packets multicasted
+# when multicasting off cache miss URLs is enabled. By
+# default this is set to 'site scope', i.e. 16.
+#Default:
+# mcast_miss_ttl 16
+
+# TAG: mcast_miss_port
+# Note: This option is only available if Squid is rebuilt with the
+# -DMULTICAST_MISS_STREAM define
+#
+# This is the port number to be used in conjunction with
+# 'mcast_miss_addr'.
+#Default:
+# mcast_miss_port 3135
+
+# TAG: mcast_miss_encode_key
+# Note: This option is only available if Squid is rebuilt with the
+# -DMULTICAST_MISS_STREAM define
+#
+# The URLs that are sent in the multicast miss stream are
+# encrypted. This is the encryption key.
+#Default:
+# mcast_miss_encode_key XXXXXXXXXXXXXXXX
+
+# TAG: mcast_icp_query_timeout (msec)
+# For multicast peers, Squid regularly sends out ICP "probes" to
+# count how many other peers are listening on the given multicast
+# address. This value specifies how long Squid should wait to
+# count all the replies. The default is 2000 msec, or 2
+# seconds.
+#Default:
+# mcast_icp_query_timeout 2000
+
+# INTERNAL ICON OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: icon_directory
+# Where the icons are stored. These are normally kept in
+# /usr/share/squid3/icons
+#Default:
+# icon_directory /usr/share/squid3/icons
+
+# TAG: global_internal_static
+# This directive controls is Squid should intercept all requests for
+# /squid-internal-static/ no matter which host the URL is requesting
+# (default on setting), or if nothing special should be done for
+# such URLs (off setting). The purpose of this directive is to make
+# icons etc work better in complex cache hierarchies where it may
+# not always be possible for all corners in the cache mesh to reach
+# the server generating a directory listing.
+#Default:
+# global_internal_static on
+
+# TAG: short_icon_urls
+# If this is enabled Squid will use short URLs for icons.
+# If disabled it will revert to the old behavior of including
+# it's own name and port in the URL.
+#
+# If you run a complex cache hierarchy with a mix of Squid and
+# other proxies you may need to disable this directive.
+#Default:
+# short_icon_urls on
+
+# ERROR PAGE OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: error_directory
+# If you wish to create your own versions of the default
+# error files to customize them to suit your company copy
+# the error/template files to another directory and point
+# this tag at them.
+#
+# WARNING: This option will disable multi-language support
+# on error pages if used.
+#
+# The squid developers are interested in making squid available in
+# a wide variety of languages. If you are making translations for a
+# language that Squid does not currently provide please consider
+# contributing your translation back to the project.
+# http://wiki.squid-cache.org/Translations
+#
+# The squid developers working on translations are happy to supply drop-in
+# translated error files in exchange for any new language contributions.
+#Default:
+# none
+
+# TAG: error_default_language
+# Set the default language which squid will send error pages in
+# if no existing translation matches the clients language
+# preferences.
+#
+# If unset (default) generic English will be used.
+#
+# The squid developers are interested in making squid available in
+# a wide variety of languages. If you are interested in making
+# translations for any language see the squid wiki for details.
+# http://wiki.squid-cache.org/Translations
+#Default:
+# none
+
+# TAG: error_log_languages
+# Log to cache.log what languages users are attempting to
+# auto-negotiate for translations.
+#
+# Successful negotiations are not logged. Only failures
+# have meaning to indicate that Squid may need an upgrade
+# of its error page translations.
+#Default:
+# error_log_languages on
+
+# TAG: err_page_stylesheet
+# CSS Stylesheet to pattern the display of Squid default error pages.
+#
+# For information on CSS see http://www.w3.org/Style/CSS/
+#Default:
+# err_page_stylesheet /etc/squid3/errorpage.css
+
+# TAG: err_html_text
+# HTML text to include in error messages. Make this a "mailto"
+# URL to your admin address, or maybe just a link to your
+# organizations Web page.
+#
+# To include this in your error messages, you must rewrite
+# the error template files (found in the "errors" directory).
+# Wherever you want the 'err_html_text' line to appear,
+# insert a %L tag in the error template file.
+#Default:
+# none
+
+# TAG: email_err_data on|off
+# If enabled, information about the occurred error will be
+# included in the mailto links of the ERR pages (if %W is set)
+# so that the email body contains the data.
+# Syntax is <A HREF="mailto:%w%W">%w</A>
+#Default:
+# email_err_data on
+
+# TAG: deny_info
+# Usage: deny_info err_page_name acl
+# or deny_info http://... acl
+# or deny_info TCP_RESET acl
+#
+# This can be used to return a ERR_ page for requests which
+# do not pass the 'http_access' rules. Squid remembers the last
+# acl it evaluated in http_access, and if a 'deny_info' line exists
+# for that ACL Squid returns a corresponding error page.
+#
+# The acl is typically the last acl on the http_access deny line which
+# denied access. The exceptions to this rule are:
+# - When Squid needs to request authentication credentials. It's then
+# the first authentication related acl encountered
+# - When none of the http_access lines matches. It's then the last
+# acl processed on the last http_access line.
+#
+# NP: If providing your own custom error pages with error_directory
+# you may also specify them by your custom file name:
+# Example: deny_info ERR_CUSTOM_ACCESS_DENIED bad_guys
+#
+# Alternatively you can specify an error URL. The browsers will
+# get redirected (302 or 307) to the specified URL. %s in the redirection
+# URL will be replaced by the requested URL.
+#
+# Alternatively you can tell Squid to reset the TCP connection
+# by specifying TCP_RESET.
+#Default:
+# none
+
+# OPTIONS INFLUENCING REQUEST FORWARDING
+# -----------------------------------------------------------------------------
+
+# TAG: nonhierarchical_direct
+# By default, Squid will send any non-hierarchical requests
+# (matching hierarchy_stoplist or not cacheable request type) direct
+# to origin servers.
+#
+# If you set this to off, Squid will prefer to send these
+# requests to parents.
+#
+# Note that in most configurations, by turning this off you will only
+# add latency to these request without any improvement in global hit
+# ratio.
+#
+# If you are inside an firewall see never_direct instead of
+# this directive.
+#Default:
+# nonhierarchical_direct on
+
+# TAG: prefer_direct
+# Normally Squid tries to use parents for most requests. If you for some
+# reason like it to first try going direct and only use a parent if
+# going direct fails set this to on.
+#
+# By combining nonhierarchical_direct off and prefer_direct on you
+# can set up Squid to use a parent as a backup path if going direct
+# fails.
+#
+# Note: If you want Squid to use parents for all requests see
+# the never_direct directive. prefer_direct only modifies how Squid
+# acts on cacheable requests.
+#Default:
+# prefer_direct off
+
+# TAG: always_direct
+# Usage: always_direct allow|deny [!]aclname ...
+#
+# Here you can use ACL elements to specify requests which should
+# ALWAYS be forwarded by Squid to the origin servers without using
+# any peers. For example, to always directly forward requests for
+# local servers ignoring any parents or siblings you may have use
+# something like:
+#
+# acl local-servers dstdomain my.domain.net
+# always_direct allow local-servers
+#
+# To always forward FTP requests directly, use
+#
+# acl FTP proto FTP
+# always_direct allow FTP
+#
+# NOTE: There is a similar, but opposite option named
+# 'never_direct'. You need to be aware that "always_direct deny
+# foo" is NOT the same thing as "never_direct allow foo". You
+# may need to use a deny rule to exclude a more-specific case of
+# some other rule. Example:
+#
+# acl local-external dstdomain external.foo.net
+# acl local-servers dstdomain .foo.net
+# always_direct deny local-external
+# always_direct allow local-servers
+#
+# NOTE: If your goal is to make the client forward the request
+# directly to the origin server bypassing Squid then this needs
+# to be done in the client configuration. Squid configuration
+# can only tell Squid how Squid should fetch the object.
+#
+# NOTE: This directive is not related to caching. The replies
+# is cached as usual even if you use always_direct. To not cache
+# the replies see the 'cache' directive.
+#
+# This clause supports both fast and slow acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Default:
+# none
+
+# TAG: never_direct
+# Usage: never_direct allow|deny [!]aclname ...
+#
+# never_direct is the opposite of always_direct. Please read
+# the description for always_direct if you have not already.
+#
+# With 'never_direct' you can use ACL elements to specify
+# requests which should NEVER be forwarded directly to origin
+# servers. For example, to force the use of a proxy for all
+# requests, except those in your local domain use something like:
+#
+# acl local-servers dstdomain .foo.net
+# never_direct deny local-servers
+# never_direct allow all
+#
+# or if Squid is inside a firewall and there are local intranet
+# servers inside the firewall use something like:
+#
+# acl local-intranet dstdomain .foo.net
+# acl local-external dstdomain external.foo.net
+# always_direct deny local-external
+# always_direct allow local-intranet
+# never_direct allow all
+#
+# This clause supports both fast and slow acl types.
+# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
+#Default:
+# none
+
+# ADVANCED NETWORKING OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: incoming_icp_average
+#Default:
+# incoming_icp_average 6
+
+# TAG: incoming_http_average
+#Default:
+# incoming_http_average 4
+
+# TAG: incoming_dns_average
+#Default:
+# incoming_dns_average 4
+
+# TAG: min_icp_poll_cnt
+#Default:
+# min_icp_poll_cnt 8
+
+# TAG: min_dns_poll_cnt
+#Default:
+# min_dns_poll_cnt 8
+
+# TAG: min_http_poll_cnt
+# Heavy voodoo here. I can't even believe you are reading this.
+# Are you crazy? Don't even think about adjusting these unless
+# you understand the algorithms in comm_select.c first!
+#Default:
+# min_http_poll_cnt 8
+
+# TAG: accept_filter
+# FreeBSD:
+#
+# The name of an accept(2) filter to install on Squid's
+# listen socket(s). This feature is perhaps specific to
+# FreeBSD and requires support in the kernel.
+#
+# The 'httpready' filter delays delivering new connections
+# to Squid until a full HTTP request has been received.
+# See the accf_http(9) man page for details.
+#
+# The 'dataready' filter delays delivering new connections
+# to Squid until there is some data to process.
+# See the accf_dataready(9) man page for details.
+#
+# Linux:
+#
+# The 'data' filter delays delivering of new connections
+# to Squid until there is some data to process by TCP_ACCEPT_DEFER.
+# You may optionally specify a number of seconds to wait by
+# 'data=N' where N is the number of seconds. Defaults to 30
+# if not specified. See the tcp(7) man page for details.
+#EXAMPLE:
+## FreeBSD
+#accept_filter httpready
+## Linux
+#accept_filter data
+#Default:
+# none
+
+# TAG: client_ip_max_connections
+# Set an absolute limit on the number of connections a single
+# client IP can use. Any more than this and Squid will begin to drop
+# new connections from the client until it closes some links.
+#
+# Note that this is a global limit. It affects all HTTP, HTCP, Gopher and FTP
+# connections from the client. For finer control use the ACL access controls.
+#
+# Requires client_db to be enabled (the default).
+#
+# WARNING: This may noticably slow down traffic received via external proxies
+# or NAT devices and cause them to rebound error messages back to their clients.
+#Default:
+# client_ip_max_connections -1
+
+# TAG: tcp_recv_bufsize (bytes)
+# Size of receive buffer to set for TCP sockets. Probably just
+# as easy to change your kernel's default. Set to zero to use
+# the default buffer size.
+#Default:
+# tcp_recv_bufsize 0 bytes
+
+# ICAP OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: icap_enable on|off
+# If you want to enable the ICAP module support, set this to on.
+#Default:
+# icap_enable off
+
+# TAG: icap_connect_timeout
+# This parameter specifies how long to wait for the TCP connect to
+# the requested ICAP server to complete before giving up and either
+# terminating the HTTP transaction or bypassing the failure.
+#
+# The default for optional services is peer_connect_timeout.
+# The default for essential services is connect_timeout.
+# If this option is explicitly set, its value applies to all services.
+#Default:
+# none
+
+# TAG: icap_io_timeout time-units
+# This parameter specifies how long to wait for an I/O activity on
+# an established, active ICAP connection before giving up and
+# either terminating the HTTP transaction or bypassing the
+# failure.
+#
+# The default is read_timeout.
+#Default:
+# none
+
+# TAG: icap_service_failure_limit
+# The limit specifies the number of failures that Squid tolerates
+# when establishing a new TCP connection with an ICAP service. If
+# the number of failures exceeds the limit, the ICAP service is
+# not used for new ICAP requests until it is time to refresh its
+# OPTIONS. The per-service failure counter is reset to zero each
+# time Squid fetches new service OPTIONS.
+#
+# A negative value disables the limit. Without the limit, an ICAP
+# service will not be considered down due to connectivity failures
+# between ICAP OPTIONS requests.
+#Default:
+# icap_service_failure_limit 10
+
+# TAG: icap_service_revival_delay
+# The delay specifies the number of seconds to wait after an ICAP
+# OPTIONS request failure before requesting the options again. The
+# failed ICAP service is considered "down" until fresh OPTIONS are
+# fetched.
+#
+# The actual delay cannot be smaller than the hardcoded minimum
+# delay of 30 seconds.
+#Default:
+# icap_service_revival_delay 180
+
+# TAG: icap_preview_enable on|off
+# The ICAP Preview feature allows the ICAP server to handle the
+# HTTP message by looking only at the beginning of the message body
+# or even without receiving the body at all. In some environments,
+# previews greatly speedup ICAP processing.
+#
+# During an ICAP OPTIONS transaction, the server may tell Squid what
+# HTTP messages should be previewed and how big the preview should be.
+# Squid will not use Preview if the server did not request one.
+#
+# To disable ICAP Preview for all ICAP services, regardless of
+# individual ICAP server OPTIONS responses, set this option to "off".
+#Example:
+#icap_preview_enable off
+#Default:
+# icap_preview_enable on
+
+# TAG: icap_preview_size
+# The default size of preview data to be sent to the ICAP server.
+# -1 means no preview. This value might be overwritten on a per server
+# basis by OPTIONS requests.
+#Default:
+# icap_preview_size -1
+
+# TAG: icap_default_options_ttl
+# The default TTL value for ICAP OPTIONS responses that don't have
+# an Options-TTL header.
+#Default:
+# icap_default_options_ttl 60
+
+# TAG: icap_persistent_connections on|off
+# Whether or not Squid should use persistent connections to
+# an ICAP server.
+#Default:
+# icap_persistent_connections on
+
+# TAG: icap_send_client_ip on|off
+# If enabled, Squid shares HTTP client IP information with adaptation
+# services. For ICAP, Squid adds the X-Client-IP header to ICAP requests.
+# For eCAP, Squid sets the libecap::metaClientIp transaction option.
+#
+# See also: adaptation_uses_indirect_client
+#Default:
+# icap_send_client_ip off
+
+# TAG: icap_send_client_username on|off
+# This sends authenticated HTTP client username (if available) to
+# the ICAP service. The username value is encoded based on the
+# icap_client_username_encode option and is sent using the header
+# specified by the icap_client_username_header option.
+#Default:
+# icap_send_client_username off
+
+# TAG: icap_client_username_header
+# ICAP request header name to use for send_client_username.
+#Default:
+# icap_client_username_header X-Client-Username
+
+# TAG: icap_client_username_encode on|off
+# Whether to base64 encode the authenticated client username.
+#Default:
+# icap_client_username_encode off
+
+# TAG: icap_service
+# Defines a single ICAP service using the following format:
+#
+# icap_service service_name vectoring_point [options] service_url
+#
+# service_name: ID
+# an opaque identifier which must be unique in squid.conf
+#
+# vectoring_point: reqmod_precache|reqmod_postcache|respmod_precache|respmod_postcache
+# This specifies at which point of transaction processing the
+# ICAP service should be activated. *_postcache vectoring points
+# are not yet supported.
+#
+# service_url: icap://servername:port/servicepath
+# ICAP server and service location.
+#
+# ICAP does not allow a single service to handle both REQMOD and RESPMOD
+# transactions. Squid does not enforce that requirement. You can specify
+# services with the same service_url and different vectoring_points. You
+# can even specify multiple identical services as long as their
+# service_names differ.
+#
+#
+# Service options are separated by white space. ICAP services support
+# the following name=value options:
+#
+# bypass=on|off|1|0
+# If set to 'on' or '1', the ICAP service is treated as
+# optional. If the service cannot be reached or malfunctions,
+# Squid will try to ignore any errors and process the message as
+# if the service was not enabled. No all ICAP errors can be
+# bypassed. If set to 0, the ICAP service is treated as
+# essential and all ICAP errors will result in an error page
+# returned to the HTTP client.
+#
+# Bypass is off by default: services are treated as essential.
+#
+# routing=on|off|1|0
+# If set to 'on' or '1', the ICAP service is allowed to
+# dynamically change the current message adaptation plan by
+# returning a chain of services to be used next. The services
+# are specified using the X-Next-Services ICAP response header
+# value, formatted as a comma-separated list of service names.
+# Each named service should be configured in squid.conf and
+# should have the same method and vectoring point as the current
+# ICAP transaction. Services violating these rules are ignored.
+# An empty X-Next-Services value results in an empty plan which
+# ends the current adaptation.
+#
+# Routing is not allowed by default: the ICAP X-Next-Services
+# response header is ignored.
+#
+# ipv6=on|off
+# Only has effect on split-stack systems. The default on those systems
+# is to use IPv4-only connections. When set to 'on' this option will
+# make Squid use IPv6-only connections to contact this ICAP service.
+#
+# Older icap_service format without optional named parameters is
+# deprecated but supported for backward compatibility.
+#
+#Example:
+#icap_service svcBlocker reqmod_precache bypass=0 icap://icap1.mydomain.net:1344/reqmod
+#icap_service svcLogger reqmod_precache routing=on icap://icap2.mydomain.net:1344/respmod
+#Default:
+# none
+
+# TAG: icap_class
+# This deprecated option was documented to define an ICAP service
+# chain, even though it actually defined a set of similar, redundant
+# services, and the chains were not supported.
+#
+# To define a set of redundant services, please use the
+# adaptation_service_set directive. For service chains, use
+# adaptation_service_chain.
+#Default:
+# none
+
+# TAG: icap_access
+# This option is deprecated. Please use adaptation_access, which
+# has the same ICAP functionality, but comes with better
+# documentation, and eCAP support.
+#Default:
+# none
+
+# eCAP OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: ecap_enable on|off
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ecap option
+#
+# Controls whether eCAP support is enabled.
+#Default:
+# ecap_enable off
+
+# TAG: ecap_service
+# Note: This option is only available if Squid is rebuilt with the
+# --enable-ecap option
+#
+# Defines a single eCAP service
+#
+# ecap_service servicename vectoring_point bypass service_url
+#
+# vectoring_point = reqmod_precache|reqmod_postcache|respmod_precache|respmod_postcache
+# This specifies at which point of transaction processing the
+# eCAP service should be activated. *_postcache vectoring points
+# are not yet supported.
+# bypass = 1|0
+# If set to 1, the eCAP service is treated as optional. If the
+# service cannot be reached or malfunctions, Squid will try to
+# ignore any errors and process the message as if the service
+# was not enabled. No all eCAP errors can be bypassed.
+# If set to 0, the eCAP service is treated as essential and all
+# eCAP errors will result in an error page returned to the
+# HTTP client.
+# service_url = ecap://vendor/service_name?custom&cgi=style&parameters=optional
+#
+#Example:
+#ecap_service service_1 reqmod_precache 0 ecap://filters-R-us/leakDetector?on_error=block
+#ecap_service service_2 respmod_precache 1 icap://filters-R-us/virusFilter?config=/etc/vf.cfg
+#Default:
+# none
+
+# TAG: loadable_modules
+# Instructs Squid to load the specified dynamic module(s) or activate
+# preloaded module(s).
+#Example:
+#loadable_modules /usr/lib/MinimalAdapter.so
+#Default:
+# none
+
+# MESSAGE ADAPTATION OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: adaptation_service_set
+#
+# Configures an ordered set of similar, redundant services. This is
+# useful when hot standby or backup adaptation servers are available.
+#
+# adaptation_service_set set_name service_name1 service_name2 ...
+#
+# The named services are used in the set declaration order. The first
+# applicable adaptation service from the set is used first. The next
+# applicable service is tried if and only if the transaction with the
+# previous service fails and the message waiting to be adapted is still
+# intact.
+#
+# When adaptation starts, broken services are ignored as if they were
+# not a part of the set. A broken service is a down optional service.
+#
+# The services in a set must be attached to the same vectoring point
+# (e.g., pre-cache) and use the same adaptation method (e.g., REQMOD).
+#
+# If all services in a set are optional then adaptation failures are
+# bypassable. If all services in the set are essential, then a
+# transaction failure with one service may still be retried using
+# another service from the set, but when all services fail, the master
+# transaction fails as well.
+#
+# A set may contain a mix of optional and essential services, but that
+# is likely to lead to surprising results because broken services become
+# ignored (see above), making previously bypassable failures fatal.
+# Technically, it is the bypassability of the last failed service that
+# matters.
+#
+# See also: adaptation_access adaptation_service_chain
+#
+#Example:
+#adaptation_service_set svcBlocker urlFilterPrimary urlFilterBackup
+#adaptation service_set svcLogger loggerLocal loggerRemote
+#Default:
+# none
+
+# TAG: adaptation_service_chain
+#
+# Configures a list of complementary services that will be applied
+# one-by-one, forming an adaptation chain or pipeline. This is useful
+# when Squid must perform different adaptations on the same message.
+#
+# adaptation_service_chain chain_name service_name1 svc_name2 ...
+#
+# The named services are used in the chain declaration order. The first
+# applicable adaptation service from the chain is used first. The next
+# applicable service is applied to the successful adaptation results of
+# the previous service in the chain.
+#
+# When adaptation starts, broken services are ignored as if they were
+# not a part of the chain. A broken service is a down optional service.
+#
+# Request satisfaction terminates the adaptation chain because Squid
+# does not currently allow declaration of RESPMOD services at the
+# "reqmod_precache" vectoring point (see icap_service or ecap_service).
+#
+# The services in a chain must be attached to the same vectoring point
+# (e.g., pre-cache) and use the same adaptation method (e.g., REQMOD).
+#
+# A chain may contain a mix of optional and essential services. If an
+# essential adaptation fails (or the failure cannot be bypassed for
+# other reasons), the master transaction fails. Otherwise, the failure
+# is bypassed as if the failed adaptation service was not in the chain.
+#
+# See also: adaptation_access adaptation_service_set
+#
+#Example:
+#adaptation_service_chain svcRequest requestLogger urlFilter leakDetector
+#Default:
+# none
+
+# TAG: adaptation_access
+# Sends an HTTP transaction to an ICAP or eCAP adaptation service.
+#
+# adaptation_access service_name allow|deny [!]aclname...
+# adaptation_access set_name allow|deny [!]aclname...
+#
+# At each supported vectoring point, the adaptation_access
+# statements are processed in the order they appear in this
+# configuration file. Statements pointing to the following services
+# are ignored (i.e., skipped without checking their ACL):
+#
+# - services serving different vectoring points
+# - "broken-but-bypassable" services
+# - "up" services configured to ignore such transactions
+# (e.g., based on the ICAP Transfer-Ignore header).
+#
+# When a set_name is used, all services in the set are checked
+# using the same rules, to find the first applicable one. See
+# adaptation_service_set for details.
+#
+# If an access list is checked and there is a match, the
+# processing stops: For an "allow" rule, the corresponding
+# adaptation service is used for the transaction. For a "deny"
+# rule, no adaptation service is activated.
+#
+# It is currently not possible to apply more than one adaptation
+# service at the same vectoring point to the same HTTP transaction.
+#
+# See also: icap_service and ecap_service
+#
+#Example:
+#adaptation_access service_1 allow all
+#Default:
+# none
+
+# TAG: adaptation_service_iteration_limit
+# Limits the number of iterations allowed when applying adaptation
+# services to a message. If your longest adaptation set or chain
+# may have more than 16 services, increase the limit beyond its
+# default value of 16. If detecting infinite iteration loops sooner
+# is critical, make the iteration limit match the actual number
+# of services in your longest adaptation set or chain.
+#
+# Infinite adaptation loops are most likely with routing services.
+#
+# See also: icap_service routing=1
+#Default:
+# adaptation_service_iteration_limit 16
+
+# TAG: adaptation_masterx_shared_names
+# For each master transaction (i.e., the HTTP request and response
+# sequence, including all related ICAP and eCAP exchanges), Squid
+# maintains a table of metadata. The table entries are (name, value)
+# pairs shared among eCAP and ICAP exchanges. The table is destroyed
+# with the master transaction.
+#
+# This option specifies the table entry names that Squid must accept
+# from and forward to the adaptation transactions.
+#
+# An ICAP REQMOD or RESPMOD transaction may set an entry in the
+# shared table by returning an ICAP header field with a name
+# specified in adaptation_masterx_shared_names. Squid will store
+# and forward that ICAP header field to subsequent ICAP
+# transactions within the same master transaction scope.
+#
+# Only one shared entry name is supported at this time.
+#
+#Example:
+## share authentication information among ICAP services
+#adaptation_masterx_shared_names X-Subscriber-ID
+#Default:
+# none
+
+# TAG: icap_retry
+# This ACL determines which retriable ICAP transactions are
+# retried. Transactions that received a complete ICAP response
+# and did not have to consume or produce HTTP bodies to receive
+# that response are usually retriable.
+#
+# icap_retry allow|deny [!]aclname ...
+#
+# Squid automatically retries some ICAP I/O timeouts and errors
+# due to persistent connection race conditions.
+#
+# See also: icap_retry_limit
+#Default:
+# icap_retry deny all
+
+# TAG: icap_retry_limit
+# Limits the number of retries allowed. When set to zero (default),
+# no retries are allowed.
+#
+# Communication errors due to persistent connection race
+# conditions are unavoidable, automatically retried, and do not
+# count against this limit.
+#
+# See also: icap_retry
+#Default:
+# icap_retry_limit 0
+
+# DNS OPTIONS
+# -----------------------------------------------------------------------------
+
+# TAG: check_hostnames
+# For security and stability reasons Squid can check
+# hostnames for Internet standard RFC compliance. If you want
+# Squid to perform these checks turn this directive on.
+#Default:
+# check_hostnames off
+
+# TAG: allow_underscore
+# Underscore characters is not strictly allowed in Internet hostnames
+# but nevertheless used by many sites. Set this to off if you want
+# Squid to be strict about the standard.
+# This check is performed only when check_hostnames is set to on.
+#Default:
+# allow_underscore on
+
+# TAG: cache_dns_program
+# Note: This option is only available if Squid is rebuilt with the
+# --disable-internal-dns option
+#
+# Specify the location of the executable for dnslookup process.
+#Default:
+# cache_dns_program /usr/lib/squid3/dnsserver
+
+# TAG: dns_children
+# Note: This option is only available if Squid is rebuilt with the
+# --disable-internal-dns option
+#
+# The number of processes spawn to service DNS name lookups.
+# For heavily loaded caches on large servers, you should
+# probably increase this value to at least 10. The maximum
+# is 32. The default is 5.
+#
+# You must have at least one dnsserver process.
+#Default:
+# dns_children 5
+
+# TAG: dns_retransmit_interval
+# Initial retransmit interval for DNS queries. The interval is
+# doubled each time all configured DNS servers have been tried.
+#
+#Default:
+# dns_retransmit_interval 5 seconds
+
+# TAG: dns_timeout
+# DNS Query timeout. If no response is received to a DNS query
+# within this time all DNS servers for the queried domain
+# are assumed to be unavailable.
+#Default:
+# dns_timeout 2 minutes
+
+# TAG: dns_defnames on|off
+# Normally the RES_DEFNAMES resolver option is disabled
+# (see res_init(3)). This prevents caches in a hierarchy
+# from interpreting single-component hostnames locally. To allow
+# Squid to handle single-component names, enable this option.
+#Default:
+# dns_defnames off
+
+# TAG: dns_nameservers
+# Use this if you want to specify a list of DNS name servers
+# (IP addresses) to use instead of those given in your
+# /etc/resolv.conf file.
+# On Windows platforms, if no value is specified here or in
+# the /etc/resolv.conf file, the list of DNS name servers are
+# taken from the Windows registry, both static and dynamic DHCP
+# configurations are supported.
+#
+# Example: dns_nameservers 10.0.0.1 192.172.0.4
+#Default:
+# none
+
+# TAG: hosts_file
+# Location of the host-local IP name-address associations
+# database. Most Operating Systems have such a file on different
+# default locations:
+# - Un*X & Linux: /etc/hosts
+# - Windows NT/2000: %SystemRoot%\system32\drivers\etc\hosts
+# (%SystemRoot% value install default is c:\winnt)
+# - Windows XP/2003: %SystemRoot%\system32\drivers\etc\hosts
+# (%SystemRoot% value install default is c:\windows)
+# - Windows 9x/Me: %windir%\hosts
+# (%windir% value is usually c:\windows)
+# - Cygwin: /etc/hosts
+#
+# The file contains newline-separated definitions, in the
+# form ip_address_in_dotted_form name [name ...] names are
+# whitespace-separated. Lines beginning with an hash (#)
+# character are comments.
+#
+# The file is checked at startup and upon configuration.
+# If set to 'none', it won't be checked.
+# If append_domain is used, that domain will be added to
+# domain-local (i.e. not containing any dot character) host
+# definitions.
+#Default:
+# hosts_file /etc/hosts
+
+# TAG: append_domain
+# Appends local domain name to hostnames without any dots in
+# them. append_domain must begin with a period.
+#
+# Be warned there are now Internet names with no dots in
+# them using only top-domain names, so setting this may
+# cause some Internet sites to become unavailable.
+#
+#Example:
+# append_domain .yourdomain.com
+#Default:
+# none
+
+# TAG: ignore_unknown_nameservers
+# By default Squid checks that DNS responses are received
+# from the same IP addresses they are sent to. If they
+# don't match, Squid ignores the response and writes a warning
+# message to cache.log. You can allow responses from unknown
+# nameservers by setting this option to 'off'.
+#Default:
+# ignore_unknown_nameservers on
+
+# TAG: dns_v4_fallback
+# Standard practice with DNS is to lookup either A or AAAA records
+# and use the results if it succeeds. Only looking up the other if
+# the first attempt fails or otherwise produces no results.
+#
+# That policy however will cause squid to produce error pages for some
+# servers that advertise AAAA but are unreachable over IPv6.
+#
+# If this is ON squid will always lookup both AAAA and A, using both.
+# If this is OFF squid will lookup AAAA and only try A if none found.
+#
+# WARNING: There are some possibly unwanted side-effects with this on:
+# *) Doubles the load placed by squid on the DNS network.
+# *) May negatively impact connection delay times.
+#Default:
+# dns_v4_fallback on
+
+# TAG: dns_v4_first
+# With the IPv6 Internet being as fast or faster than IPv4 Internet
+# for most networks Squid prefers to contact websites over IPv6.
+#
+# This option reverses the order of preference to make Squid contact
+# dual-stack websites over IPv4 first. Squid will still perform both
+# IPv6 and IPv4 DNS lookups before connecting.
+#
+# WARNING:
+# This option will restrict the situations under which IPv6
+# connectivity is used (and tested), potentially hiding network
+# problem swhich would otherwise be detected and warned about.
+#Default:
+# dns_v4_first off
+
+# TAG: ipcache_size (number of entries)
+#Default:
+# ipcache_size 1024
+
+# TAG: ipcache_low (percent)
+#Default:
+# ipcache_low 90
+
+# TAG: ipcache_high (percent)
+# The size, low-, and high-water marks for the IP cache.
+#Default:
+# ipcache_high 95
+
+# TAG: fqdncache_size (number of entries)
+# Maximum number of FQDN cache entries.
+#Default:
+# fqdncache_size 1024
+
+# MISCELLANEOUS
+# -----------------------------------------------------------------------------
+
+# TAG: memory_pools on|off
+# If set, Squid will keep pools of allocated (but unused) memory
+# available for future use. If memory is a premium on your
+# system and you believe your malloc library outperforms Squid
+# routines, disable this.
+#Default:
+# memory_pools on
+
+# TAG: memory_pools_limit (bytes)
+# Used only with memory_pools on:
+# memory_pools_limit 50 MB
+#
+# If set to a non-zero value, Squid will keep at most the specified
+# limit of allocated (but unused) memory in memory pools. All free()
+# requests that exceed this limit will be handled by your malloc
+# library. Squid does not pre-allocate any memory, just safe-keeps
+# objects that otherwise would be free()d. Thus, it is safe to set
+# memory_pools_limit to a reasonably high value even if your
+# configuration will use less memory.
+#
+# If set to none, Squid will keep all memory it can. That is, there
+# will be no limit on the total amount of memory used for safe-keeping.
+#
+# To disable memory allocation optimization, do not set
+# memory_pools_limit to 0 or none. Set memory_pools to "off" instead.
+#
+# An overhead for maintaining memory pools is not taken into account
+# when the limit is checked. This overhead is close to four bytes per
+# object kept. However, pools may actually _save_ memory because of
+# reduced memory thrashing in your malloc library.
+#Default:
+# memory_pools_limit 5 MB
+
+# TAG: forwarded_for on|off|transparent|truncate|delete
+# If set to "on", Squid will append your client's IP address
+# in the HTTP requests it forwards. By default it looks like:
+#
+# X-Forwarded-For: 192.1.2.3
+#
+# If set to "off", it will appear as
+#
+# X-Forwarded-For: unknown
+#
+# If set to "transparent", Squid will not alter the
+# X-Forwarded-For header in any way.
+#
+# If set to "delete", Squid will delete the entire
+# X-Forwarded-For header.
+#
+# If set to "truncate", Squid will remove all existing
+# X-Forwarded-For entries, and place itself as the sole entry.
+#Default:
+# forwarded_for on
+
+# TAG: cachemgr_passwd
+# Specify passwords for cachemgr operations.
+#
+# Usage: cachemgr_passwd password action action ...
+#
+# Some valid actions are (see cache manager menu for a full list):
+# 5min
+# 60min
+# asndb
+# authenticator
+# cbdata
+# client_list
+# comm_incoming
+# config *
+# counters
+# delay
+# digest_stats
+# dns
+# events
+# filedescriptors
+# fqdncache
+# histograms
+# http_headers
+# info
+# io
+# ipcache
+# mem
+# menu
+# netdb
+# non_peers
+# objects
+# offline_toggle *
+# pconn
+# peer_select
+# reconfigure *
+# redirector
+# refresh
+# server_list
+# shutdown *
+# store_digest
+# storedir
+# utilization
+# via_headers
+# vm_objects
+#
+# * Indicates actions which will not be performed without a
+# valid password, others can be performed if not listed here.
+#
+# To disable an action, set the password to "disable".
+# To allow performing an action without a password, set the
+# password to "none".
+#
+# Use the keyword "all" to set the same password for all actions.
+#
+#Example:
+# cachemgr_passwd secret shutdown
+# cachemgr_passwd lesssssssecret info stats/objects
+# cachemgr_passwd disable all
+#Default:
+# none
+
+# TAG: client_db on|off
+# If you want to disable collecting per-client statistics,
+# turn off client_db here.
+#Default:
+# client_db on
+
+# TAG: refresh_all_ims on|off
+# When you enable this option, squid will always check
+# the origin server for an update when a client sends an
+# If-Modified-Since request. Many browsers use IMS
+# requests when the user requests a reload, and this
+# ensures those clients receive the latest version.
+#
+# By default (off), squid may return a Not Modified response
+# based on the age of the cached version.
+#Default:
+# refresh_all_ims off
+
+# TAG: reload_into_ims on|off
+# When you enable this option, client no-cache or ``reload''
+# requests will be changed to If-Modified-Since requests.
+# Doing this VIOLATES the HTTP standard. Enabling this
+# feature could make you liable for problems which it
+# causes.
+#
+# see also refresh_pattern for a more selective approach.
+#Default:
+# reload_into_ims off
+
+# TAG: maximum_single_addr_tries
+# This sets the maximum number of connection attempts for a
+# host that only has one address (for multiple-address hosts,
+# each address is tried once).
+#
+# The default value is one attempt, the (not recommended)
+# maximum is 255 tries. A warning message will be generated
+# if it is set to a value greater than ten.
+#
+# Note: This is in addition to the request re-forwarding which
+# takes place if Squid fails to get a satisfying response.
+#Default:
+# maximum_single_addr_tries 1
+
+# TAG: retry_on_error
+# If set to ON Squid will automatically retry requests when
+# receiving an error response with status 403 (Forbidden),
+# 500 (Internal Error), 501 or 503 (Service not available).
+# Status 502 and 504 (Gateway errors) are always retried.
+#
+# This is mainly useful if you are in a complex cache hierarchy to
+# work around access control errors.
+#
+# NOTE: This retry will attempt to find another working destination.
+# Which is different from the server which just failed.
+#Default:
+# retry_on_error off
+
+# TAG: as_whois_server
+# WHOIS server to query for AS numbers. NOTE: AS numbers are
+# queried only when Squid starts up, not for every request.
+#Default:
+# as_whois_server whois.ra.net
+
+# TAG: offline_mode
+# Enable this option and Squid will never try to validate cached
+# objects.
+#Default:
+# offline_mode off
+
+# TAG: uri_whitespace
+# What to do with requests that have whitespace characters in the
+# URI. Options:
+#
+# strip: The whitespace characters are stripped out of the URL.
+# This is the behavior recommended by RFC2396.
+# deny: The request is denied. The user receives an "Invalid
+# Request" message.
+# allow: The request is allowed and the URI is not changed. The
+# whitespace characters remain in the URI. Note the
+# whitespace is passed to redirector processes if they
+# are in use.
+# encode: The request is allowed and the whitespace characters are
+# encoded according to RFC1738. This could be considered
+# a violation of the HTTP/1.1
+# RFC because proxies are not allowed to rewrite URI's.
+# chop: The request is allowed and the URI is chopped at the
+# first whitespace. This might also be considered a
+# violation.
+#Default:
+# uri_whitespace strip
+
+# TAG: chroot
+# Specifies a directory where Squid should do a chroot() while
+# initializing. This also causes Squid to fully drop root
+# privileges after initializing. This means, for example, if you
+# use a HTTP port less than 1024 and try to reconfigure, you may
+# get an error saying that Squid can not open the port.
+#Default:
+# none
+
+# TAG: balance_on_multiple_ip
+# Modern IP resolvers in squid sort lookup results by preferred access.
+# By default squid will use these IP in order and only rotates to
+# the next listed when the most preffered fails.
+#
+# Some load balancing servers based on round robin DNS have been
+# found not to preserve user session state across requests
+# to different IP addresses.
+#
+# Enabling this directive Squid rotates IP's per request.
+#Default:
+# balance_on_multiple_ip off
+
+# TAG: pipeline_prefetch
+# To boost the performance of pipelined requests to closer
+# match that of a non-proxied environment Squid can try to fetch
+# up to two requests in parallel from a pipeline.
+#
+# Defaults to off for bandwidth management and access logging
+# reasons.
+#
+# WARNING: pipelining breaks NTLM and Negotiate/Kerberos authentication.
+#Default:
+# pipeline_prefetch off
+
+# TAG: high_response_time_warning (msec)
+# If the one-minute median response time exceeds this value,
+# Squid prints a WARNING with debug level 0 to get the
+# administrators attention. The value is in milliseconds.
+#Default:
+# high_response_time_warning 0
+
+# TAG: high_page_fault_warning
+# If the one-minute average page fault rate exceeds this
+# value, Squid prints a WARNING with debug level 0 to get
+# the administrators attention. The value is in page faults
+# per second.
+#Default:
+# high_page_fault_warning 0
+
+# TAG: high_memory_warning
+# If the memory usage (as determined by mallinfo) exceeds
+# this amount, Squid prints a WARNING with debug level 0 to get
+# the administrators attention.
+#Default:
+# high_memory_warning 0 KB
+
+# TAG: sleep_after_fork (microseconds)
+# When this is set to a non-zero value, the main Squid process
+# sleeps the specified number of microseconds after a fork()
+# system call. This sleep may help the situation where your
+# system reports fork() failures due to lack of (virtual)
+# memory. Note, however, if you have a lot of child
+# processes, these sleep delays will add up and your
+# Squid will not service requests for some amount of time
+# until all the child processes have been started.
+# On Windows value less then 1000 (1 milliseconds) are
+# rounded to 1000.
+#Default:
+# sleep_after_fork 0
+
+# TAG: windows_ipaddrchangemonitor on|off
+# On Windows Squid by default will monitor IP address changes and will
+# reconfigure itself after any detected event. This is very useful for
+# proxies connected to internet with dial-up interfaces.
+# In some cases (a Proxy server acting as VPN gateway is one) it could be
+# desiderable to disable this behaviour setting this to 'off'.
+# Note: after changing this, Squid service must be restarted.
+#Default:
+# windows_ipaddrchangemonitor on
+
+# TAG: max_filedescriptors
+# The maximum number of filedescriptors supported.
+#
+# The default "0" means Squid inherits the current ulimit setting.
+#
+# Note: Changing this requires a restart of Squid. Also
+# not all comm loops supports large values.
+#Default:
+# max_filedescriptors 0
+